Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I opened both the NordicSemiDemo.xcodeproj and nRFDemo.xcodeproj in Xcode 5.0.2. When I try to run them (Product->Run), I get the splash screen in the simulator, but when...
this time i have some encryption related questions to ask.
I use the "BLE_GAP_CONN_SEC_MODE_SET_XXX" to enble link encryption, doese this correct?
can i set the encryption...
Quick question regarding the boot process of the nrf51822. If a bootloader address is written to 0x10001014, will the bootloader code always be executed, regardless of whether...
Hi
I am using ble_app_hrs for my application.
in this case ble has highest priority , next gpio then timer.
if i send continuous data over ble, by using function...
Hello Nordic expert,
In nRF51822_PS_v1_3, the max bit rates for SPI master is 8Mbps(section 8.8, page43).
But in nRF51822_PS_v2.0, the max bit rates for SPI master change...
I heared a rumour that the NRF581922 will be withdrawn and an other solution will become available. We have planned the 581922 for implementation and want te release the product...
/* YOUR_JOB: Use an appearance value matching the application's use case.
err_code = sd_ble_gap_appearance_set(BLE_APPEARANCE_);
APP_ERROR_CHECK(err_code); */
Shoult...
Do I still have to call sd_ble_gatts_value_set() on the characteristic handle [using whatever temporary buffer I would have been using anyway for BLE_GATTS_VLOC_STACK]?
...
Hi,
I would like to use the app_gpiote files from Nordic in combination with the softdevice enabled.
In the app_gpiote.c file interrupts are enabled using the standard...
As far as I can see buttons_init() initializes GPIO and sets up button_event_handler().
button_event_handler() calls ble_lbs_on_button_change() and always set static uint8_t...
I have problems with my iPad to catch data coming from key presses of HID keyboard profile. First, I programmed the dev tool nRF6310+PCA10005 with the HID keyboard profile...
I installed nrfgostudio_win-64_1.15.1_installer, nrfgo_sdk_2.3.0_setup and nrfprobe_v2_0_0_7252 to test nRFgo starter kit(nRF6700). I tried to test uart on nRF24LE1D. but...
I want to establish a link between two nRF8001 devices. Is there an example of how to do it? I am using micro controller on our application board to control the nRF8001 devices...
Dear Developer Zone,
At this time, it is possible to upgrade the firmware version using Bootloader. But, is there any way or any plan to upgrade also the softdevice version...
