We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
i am developing under NCS 3.2.1.
I would like to if there exist a stand-alone command for creating DFU (nrfutil sub-command or similar) instead of https://github.com...
Hi guys, I have been working with a custom PCB based around the nRF5340 that uses the nPM1100 as the PMIC. I have configured it for 1V8 VOUTB output, fixed VBUS, VTERM high...
Hello, in the design reference it explicitly mentions:
“Important note on C9: The grounding of the C9 capacitor MUST be isolated from ALL ground layers except the bottom...
Hello,
I’ve been using SSD1306 128x64 OLED displays with nRF52840 boards for several years without any issues, building with nRF Connect SDK 2.5.x to 3.1.0. Recently, I...
We have thousands of devices live in production and we sometimes encounter the situation that we cannot restart bluetooth advertising anymore after a connection attempt. ...
Hi, we are investigating some devices in field, and have limited logs to work with. From time to time, we see EMM reports with cause 255. According to nRF9160 AT Commands...
Hello,
I have been following the tutorial for the DECT NR+ Shell (nRF91x1: DECT NR+ Shell). However, I am unable to locate the sample referenced in the documentation:
...
Hello, I try to do work a ism330dhcx on a custom digital board with a custom board in which there is a NRF54L15 microcontroller. The sensor works on other custom board with...
Hi all, I'm currently evaluating a few different vendors, chips and technologies for an idea I've had. It's a wireless+USB gaming HID, so latency is very important. 1kHz polling...
Hello,
We are planning to use the nRF54LM20A, but we do not intend to implement USB in our design.
For the nRF52 series, the datasheet provides a reference schematic for...
Hello all,
Please let me know which module we can use for mesh networking for home automation project (lighting control through smartphone app),maximum how many devices...
Hi, we are currently implementing DECT NR+ mesh network as part of a thesis, where our one part of our plan was to implement full MAC layer (otherwise its just a full mesh...
Hi,
I'm trying to write a generic tool that lists the attribute table of a connected BLE Peripheral. For each discovered attribute I want to log to the console the attribute...
Hello,
I am trying to determine if it is possible to have those 3 stacks coexisting.
I have an iSP4520 chip, which includes an nRF52832 (BLE and Wirepas) and Semtech SX1262...
Hi,
We’re currently integrating the nRF54 series into a product we’re developing, and we’re using the reference schematic and layout as our guide.
While working through...
