Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
When I launch the Power Profile in nRF Connect for Desktop, the following log appears, and it cannot connect to the PPK:
The versions of each application are as follows...
As the question explained. I want to know if we can implement all three zigbee roles viz, Edge, Router and Co-Ordinator in a single project and can be able to switch them...
Dear Nordic Team,
We are working on a solution where we want to only connect to a certain device if it is a known device and not accept any random requests.
We believe...
Hi ,Nordic
nrfx_err_t nrfx_pdm_buffer_set(int16_t * buffer, uint16_t buffer_length)
I wonder the buffer is PDM buffer or PCM buffer ?
also want to know that how...
Dear support team, The customer used ncs2.6.0 to run on nRF52840 to make matter over thread smart door lock. When stress testing the switch lock (repeat: password unlock ...
I 'm using zephyr to create a custom nrf52832 board .
I 'm using the Devicetree Visual Editor .
Any idea why I can 't select this specific display controller ?
The datasheet...
Hello, As for my peripheral BLE NUS service under NCS 1.9.2, when I search and connect it from my Windows PC running nRF Connect for Desktop BLE Standalone 4.0.0, I found...
I am sending data from iOS to a nRF5340DK. I have some code showing the TX/RX MTU Size:
Which shows: Updated MTU: TX: 527 RX: 498 bytes
But on the iOS/Controller...
Hello!
As stated in the subject, when I followed the steps in the chapter of running OTBR using Docker ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols...
Hi, am using the nrf52dk with nrf52832, nrf coonect sdk 2.5.1/ toolchain 2.5.2 and am building a prototype to aquire the signal from the ckp and cmp sensor in the car when...
Greetings,
We switched from nrf9160 to nrf9161 and got the first boards manufactured. NRF9160 has been working fine but we wanted improved GNSS functionality on board. ...
Hi all,
I have plenty of experience with the Old SDK, IAR/Keil/SES, nRF51, nRF52, Soft Device, etc. However, I'm new to the nRF Connect SDK, VS Code and nRF5340. I've successfully...
Please let us know which PINs of nrf5340 are used by BLE stack and which pins are used by peripherals like UART0 and UART1? We are converting our code from nrf connect V 1...
Hello,
We are evaluating MCU's for a low cost Central device that is extremely cost constrained. The nRF52805 and the nRF52810 both have the same RAM (24 KB) and FLASH ...
Hello,
I'm stuck in the nRF Connect SDK Fundamentals course on lesson 3, exercise 1. When opening the COM port to view the printk messages, I get an error when connecting...
