Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi, I'm trying to read data from an LIS2DH accelerometer using the nRF5340 DK board. I have been able to build and flash my code to the board, but the terminal outputs, "Device...
I have a product that has a bug and I'm forced to go thru some older code. This was the nrf24 plus chip. The code still runs fine, and most of the function I created do all...
Hi.
I want to implement software PWM on nRF52810 microcontroller, I took this project as a basic example -->
But when I enable CONFIG_PWM_NRF5_SW=y in the prj.conf file...
I just updated to Power Profiler 4.2.0 and PPK2 firmware 1.2.0 and now I see the big changes with the exact same DUT and setup compared to the Power Profiler 4.1.2:
* Current...
Hello support team, i have an issue regarding the i2c configuration on an nrf52832.
The Setup is:
EvalBoard nrf52dk_52832
BME280 Sensor attached via I2C
NCS 2.6...
Hi
I am trying to build an nrf5340 audio dk application from the command line. I can build the project using the normal vscode code extension, though I cannot build it...
When I add CONFIG_LTE_EDRX_REQ=y to prj.conf I get an "No heap space for incoming notification" error. I already tried to double the size of CONFIG_HEAP_MEM_POOL_SIZE =8192...
For our project we switched over to using DIRECT_XIP mone primarily because of the faster boot time but it automatically enables downgrade protection. For our project we need...
Hi,
I want to measure a unit current in production.
When connecting the unit to the batteries it do some beeps and after a while goes to sleep.
I want to test the "sleep...
Hi all ,
I 'm currently developping a BLE central with Zephyr and I need to create a default bonded device at startup (I know its address + IRK ) .
Using previous nRF...
Hello, I am trying to create an application on the nRF5340 which samples data at 16kHz and packages + sends it over BLE. This requires a BLE throughput ~1Mbps, which I can...
I am using MX25 external flash with nRF9160. I am unable to find the configuration to use the Zephyr APIs to access the flash. I am able to access it when I am using
spi_write_dt...
Dear Nordic Semiconductor Team,
I am a representative of ELKO EP company and we are currently in the process of obtaining FCC certification for our products that utilize...
I'm using the nrf7002 on a custom PCB, so its a brand new chip. I haven't done any OTP programming for the mac address and instead it's just a hardcoded mac address that's...
Hello Support Team,
I hope this message finds you well.
I've been experimenting with the LittleFS sample available at the following link: LittleFS Sample Code . The sample...
