But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello developers, I am using nRF52833 chip for Mesh sensor application.
The picture below is my mesh network model. 1. The model includes devices such as Sensor Server,...
When trying to compile a zigbee light switch example for the nrf5340-cpu_app target using visual studio using the zigbee fota prj file, the application compiles only once...
brief:
The Zigbee version fo the example was ported to matter. Both standards use ZAP files for the definitions, but have smaller differences in their specification. The...
Hello, I am aiming to compile a project with SES studio, version 6.40 . The target is nRF52dk. I have the following issue: 1.\
Generating linker script ‘SmartShelfPusher...
Hello everyone,
So I'm trying to build for a custom nRF9160 board. I've copied the Thingy:91 board and renamed all files and edited the cmake , as per the guide and video...
I'm trying to run the Hello World example in VS Code. When I launch the IDE, I can see that there is an error "No Kit Selected". When I attempt to install a Kit and hit the...
Hello.
I'm trying to connect to nordic device, but only connects randomly.
The logs of Android in attachment.
Android version: 11
The java code:
The...
Hi guys,
I'm working to test how much performance I can get out of the mesh implementation. I'm using the BT_MESH_MODEL_ID_SENSOR_SRV ID to create a custom model type, and...
Hi,
We have an application scanning 4 ADC inputs AN1, AN5, AN6 and AN7
We setup the SSADC in scanning mode:
We start sampling the ADC on a regular basis using PPI...
Hi,
I'm using a custom nrf52832 board (picture below), and I'm using nRF Connect SDK in visual code studio. I'm new to nRF so I'm a little confused about programming custom...
Dear Nordic,
We are developing nRF21540 + nRF5340 solution.
As there seems to be many versions of matching components depending on which source of information is used...
Hello,
I am currently developing a firmware where I am acting as a server with nRF52840.
The protocol of my use case is:
Client is connecting to my device (server...
NRF52: SDK v2.1.1
NRF91/SLM: SDK v2.0.0
We are seeing an issue with NRF52840 / NRF91 interaction over LPUART. When NRF91 powers up, the bootloader is not using using LPUART...
hi dev
I have a question about nrf52 dk board.
I have 2 dk board : one was written 2021.06 and the other one was written 2022.12
anyway, when I debug same file which...
We have a custom nRF9160 board which in Zephyr v1.7.1 defined in the boards\arm tree. It is a near copy of the nrf9160dk_nrf9160 folder with hardware changes and additions...
