Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I would like to use GPIOTE, PPI, and TIMER to do the following.
I'm using three GPIO pins. Each pin will get square-wave like signals of varying frequency. On each pin I...
Hi Nordic:
we want to add timesync function on nrf5340 ble nus.(1central + 16peripherals, 0.1ms precision )
Such as:
https://github.com/nordic-auko/nRF5-ble-timesync...
Hi,
Can I know how to set the UICR as the default address in nRF52840 SOC with SDK 17.02/17.1.0 by using nRFJPROG command line tool / SEGGER Embedded Studio IDE.
nRFJPROG...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I managed to implement a multilink communication...
Hi, i was working on a project and from one day to the next i am no longer able to flash my DevBoard.
When pluging it in it comes up as "E:\" name JLINK as always, but west...
We have a board that is to be certified by a Chinese test lab, so I need to create an image based on the direct_test_mode sample.
In Zephyr v2.0.0 I created a custom board...
Hello,
We are using nRF Connect SDK 2.0 on an nRF52832 and were wondering if it is possible to use BLE and Shockburst simultaneously? If I compile enabling both Shockburst...
Hello,
A couple of days ago I run the examples direction_finding_connectionless_rx and tx on two nRF52833dk successfully, meaning that I could see the CTE info received...
Hello,
I have reconfigured the nrf_dm sample from ncs 2.0.0 to use Zephyr Bluetooth Controller by adding CONFIG_BT_LL_SW_SPLIT=y to proj.conf.
But then it's stuck in this...
i am using the uart0 on a nrf52840 to communicate with an quectel bg95 using async api (dma) on zephyr 3.1.
from the uart interface there are connected rxd, txd, rts and...
Hi,
I am attempting to merge two example programs together and have hit an issue with a hard fault when my timer interrupt triggers.
This works fine in the standalone...
I refer to https://github.com/alc6/nrf52-pc10040-multiperipheral-passkey/blob/master/main.c for implementing static passkey. But pm_sec_params_set() returns errCode=0x7. ...
What I've done
1) Set up ot-br on an Rpi4 by following this guide .
2) Set up a 52840Dongle (plugged into the RPi4) as RCP by following this guide .
3) Installed the...
