Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I have just configured Wireshark 3.6.5 with nRF Sniffer 4.1.0 on the PC with Windows10, but I am not able to select column "Destination" to be shown. It is not present on...
I want my device to continuously advertise and if there is no advertising in between, at that time device should be in sleep mode, I've used idle_state_handle(); but still...
The default Kconfig option for the MCUBoot swap algorithm is CONFIG_BOOT_SWAP_USING_MOVE, which corresponds to:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hello,
I'm on the development of a biomedical application using nrf52832 module. Would like to know if the CPU core can be able to isolate itself (ignore all incoming interrupts...
I have watched your distance measurement webinar.
We want to use the distance measurement tool in our thread network, but I do not know how the synchronisation should be...
Peripheral: nRF52832
IDE: SES
SDK: nRF5 17.0.2
Hi,
I am attempting to jump from a non-BLE application to a BLE application. I was successful in modifying the "secure_bootloader...
Hi，
I have a question of my "PCA10056 boad", The VDD_NRF voltage is only 1.7V when connect microUSB of J2, I think one of my board components is broken, can you gei me some...
Hi,
I'm using nRF52805 with LIS2DW, accelerometer.
LIS2DW is controlled by I2C protocol. but I do not use nrf I2C driver. I am using two GPIO port emulating I2C. It works...
Hi,
Regarding QSPI, could I use the QSPI feature to fetch stored sensor data directly from the flash and send it via Bluetooth module, or is it only to increase the application...
Hi,
I have two nRF52833 and i want to make one tx and one rx (with an antenna array) for direction finding (AOA mode).
I have already compile the project called "direction_finding_connectionless_tx...
Hi I'm developing an application using SoC nRF52840 and I need to use load cells to measure some weights. A lot of existing solutions use the HX711 chip to amplify the differential...
Is there any peripheral sample for OOB legacy pairing? I'd like to know how to encrypt with temporary key( TK). I checked the ble_hids_keyboard_pair_nfc sample in the SDK...
Hello ,
I'm using the libuarte library so i can send data and receive it , i'm enabling RTC2,TIMER1,TIMER0 and TIMER2 .
this is the main definition of my libuarte NRF_LIBUARTE_ASYNC_DEFINE...
Hello,
As we are close to production of our new device, i would like to know what are the possible ways of performing OTA DFU in thread network from Thread Border Router...
I have interfaced two ESP32's with ESP-NOW protocol in which one esp32#1 sends the data to the other esp32#2. I am able to send the data from esp32#1 and receive that data...
