At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a.
Here my application sends 240 bytes of data every 150 ms. But after sending few...
Hi,
I use the a gpiote_in_event to trigger a number of PWM pulses which works fine so far. However, the exact behaviour of the generated signal is important so that the...
Hello, I am using nRF52-DK with Segger Embedded Studio and I'm running the following code that first blinks the LED1 on&off 5 times, and sets up BUTTON1 for wake up, and then...
Hi,
I would like to read the temperature of the nRF.
I tried to use the routine I found here in the forum
Sometimes works sometimes the system crash. I notice the...
Hi
I am using NRF5340 chip in my custom board to communicate serially with an external device whose data length is more than 128 bytes.
The chip can receive 243 bytes...
I am looking for the examples for the SDK. I installed SDK 1.9.1 through the Toolchain Manager and see the directory "users/my_user_name/ncs/v1.9.1" Supposedly this is where...
Hi,
In Openthread's Coap_client sample, Following 2 libraries are there:
and while compiling my code I get multiple warning regarding to above 2 libraries.
Following...
Hi,
I have problem to use bmi160 library with nrf5340 in spi connection.
I use the example application zephyr/samples/sensor/adxl372 and change the sensor to bmi160 (...
Hi DevZone ! Here is my issue: I use to work with VSCode and nRF Connect for desktop for a few months now. Early on Monday, I did uninstall all my dev environment (VSCode...
Hi,
is there any way to get a Pin to a defined "high" without vdd-gpio ref?
In our situation the NRF9160 Power is a Battery with 4,1V and the VDD-GPIO is 3,3V with a regulator...
I created two build configurations a Debug and a Release in SES IDE.
Build > Build Configurations...
I wanted to select the DEBUG_OPTIMIZATIONS level for the Debug build...
This is a continuation of the topic here that is now closed
https://devzone.nordicsemi.com/f/nordic-q-a/85590/nrf9160-azure_iot_hub-change-dps-username-during-run-time ...
Hi, I want to update the modem firmware devices(in the field).I am using nRfconnect sdk 1.5.0 and hardware is brf9160 SICA B1 . current modem firmware is 1.2.3 . I tried to...
I tried to define an event as in attached figure. During Build, the error in the as shown in the attached imageoccurs. Where to define Log Configurations ? I ading custom...
cpu info:nrf5340
software:nrf connect sdk 1.6.1
hi professor,
In the uart interrupt I call k_fifo_put to trigger rx process thread but it is not take effect.What person...
