Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hello,
Is it possible to receive a review for a board i'm developing??
This board is to be used as a Raspberry Pi Hat to be able to communicate using UART between RPi...
How to recover communication due sequence number. (Could be due of PYACI serial hardware changed/dammaged). Is there any command to reset or know sequence number of node....
Hello all,
I'm developing a BLE CGMS application based on the experimental example on the SDK folder.
Now I working in the timing characteristics and I could see that...
It looks to me like there's usage of the 32 bit milisecond timer in the mqtt client.
It seems to me that mqtt_elapsed_time_in_ms_get(...) could calculate an incorrect elapsed...
We're using the nRF9160 with an external main microcontroller, and communicating with it over SPI. We're evaluating the lowest power modes of our custom hardware to make sure...
1. I want to minimize current consumption (5uA - 10uA) in nrf52832.
2. We are using the soft devices in it.
3. Please tell me all possible SDK configuration settings for...
Hello all,
I have a BLE central application based on nRF Connect SDK V1.6.1 and a BLE peripheral application based on nRF5 SDK 17.1.0. The peripheral wakes up on interrupt...
Hi
For the qualification we need to know the values of the parameters listed below. Our hardware uses a nRF52805 and can operate in both ESB and BLE mode.
Operating...
Hello Devzome Users,
I have a problem with running my codes on other computers. The project runs on my PC very well which I coded original.
I would like to test it on...
Hello Nordic,
I've acquired several nrf52-dks and I use them almost exclusively to flash with nrfConnect on the PC.
To learn more about nrf programming I started with...
Hi all,
May I know is the antenna array a built in in 5340 DK or not? According to https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/direction_finding_connectionless_rx...
Hey all, I've been learning/working on the 53 and have had some issues adding in the AMG8 example. i've gotten the sensor to work flawlessly on an STM32 & nordic 52 but am...
Hello to all,
I have a question about parsing zigbee commands when they present a payload.
In the Window Covering device I use the define "ZB_ZCL_WINDOW_COVERING_GET_GO_TO_LIFT_PERCENTAGE_REQ...
Hi support team,
I'm learning about distance calculation based on time of flight. I only have nrf52832DK here but i wanted to try. I'm looking for an example of getting...
Hello,
Power Profiler v3.1.3
Windows 10 Home 21H1
On Data Logger tab and , regardless of if a PPK2 has been connected or not, and regardless of any of the values...
