Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hi, I'm trying to run the JLink debugger using Ozone to debug my program. When I run nrf_crypto_init(), I encounter a hard-fault. The program is not experiencing any problem...
Hi,
I am trying to develop an application on nRF52840 development kit board. When I am trying to build I am getting below error "nrfx.h: No such file or directory". For...
I am trying to port BLE_APP_Interactive to nRF52840 as I require 2 uarts in my application and larger memory. I realise I need to change the crypto to CC310, and I have followed...
I've been seeing issues with getting an interrupt on the TX side. I reckon it could also be linked to the RX module cause if the payload isn't sent, the interrupt on the TX...
Hi,
I have implemented a custom bootloader/firmware package, but have recently been running into issues when integrating the two. I have found in some instances when using...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
When trying to build/run the btle throughput demo I get a device not supported error.
When looking in the Options - Device settings for
the project the Software Packs...
Hi All,
the logging output (NRF_LOG_...) in the SDK17 via the UART works fine on the DK board (only change from the HRS example was the NRF_LOG_BACKEND_UART_TX_PIN has been...
I am using nrf mesh SDK 4.0 with nrf52832 DK and nrf mesh android app , with the light switch exemple , i noticed that a proxy node that was successfully provisioned can be...
Hi,
My aim is on button press in peripheral side ,it should do advertise and sent data from single peripheral to multiple central(total two central).
I am using nrf52810...
Hi,
I am using nRF52840 SoC as a thread device in my application. I want to push data from sensors to cloud. So I need to configure one of my thread devices as border...
Hi Dev team,
I had an issue regarding getting the real time using RTC. I tried to follow the below dev zone blog but the CAL_RTC does not work in my code.
As such, I am...
To the kind attention of Nordic support team,
We are doing EMC pre-tests of our products using your nRF52833 .
At this stage, nRF52833 device is triggering itself a...
Hello.
I am following this tutorial, but unfortunately I am stuck at step 7. I am not sure which characteristic corresponds to the UART RX characteristic value.
I tried...
I've started an asset tracking project at the company that I work at and have tried to use the nrf9160 dev kit for the device tracking part.
I have updated the board firmware...
