We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi, I want to test sending multiple packets of data with each packet having the maximum possible size of 247 bytes. I am currently testing with nRF Connect app. When i try...
I use nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac.
Example nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\thread\cli\uart\pca10056.
define BOARD_PCA10059.
...
I am using nrf51822. Separately BLE and flash are working perfectly alright. But when I comment err_code = ble_advertising_start(BLE_ADV_MODE_FAST); this line flash is working...
Hello,
As per my understanding, SPP was supported by BT Classic and no more supported in BLE. I have a device, which runs SPP. It has to be connected to the BLE client....
Hi, I am now developing a product which uses nrf51422 chip. In this product, I use buttons to turn on and off (since I don't have hard-power cut off circuit, we use system...
Hi
I wonder if the SDK DTM example can be used with a Rhode & Schwarz CMW500 unit. Are the commands compatible with each other, i.e. expected by the CMW500 and DTM example...
Hi,
we're evaluating NRF52 as a platform for a project in the agricultural space and I have some beginner's questions:
Is it feasible to use a timer firing at 100kHz...
Hello,
I created a custom board with the BMD350 module (it has a nRF52832 chip), and I a trying to program it with the BMD300 eval board.
The module on my custom board...
I am using a nRF51422 device with the SDK 11. The task is to transmit battery service data to an application on the phone. I was wondering if there is a tutorial available...
Hi,
I used "ble_image_transfer" sample code and can get the all the stuff I want and now I'm implementing the central device for it,
but somehow I always got the "cccd_configure...
SDK 14.0.0/S132 5.0.0
When a whitelist is in use and during a connection, a call to ble_start_advertising is made to change advertising to a non-connectable type
since...
This keeps happening every time I stop the program for a while and then resume execution.
N.B. I did put a breakpoint trying to catch the problem.
Softdevice s132 6...
Hi All,
I have more boards on which I have loaded the code ble_app_uart_c (nRF5_SDK_15.2.0_9412b96) which I use as central devices and I have other boards on which I have...
I need to send the following sequence of bits through TWI
start bit | 7 bit address | write | slave ACK | stop bit
I looked through the twi_hw_master.c and it seems...
