Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
I am developing a Zigbee sensor device based on the nRF52840. I have based my firmware on the "Thingy:53: Zigbee weather station" sample. This means it is a Sleepy End Device...
HI
SDK Version : nRF5_SDK_17.1.0_ddde560
Softdevcie : S132
I'm looking for resources on DevZone to use AES128. I looked up the content and found that when bonding is...
If I use zb_zdo_mgmt_lqi_req() for dst_addr = local short address is the response resolved internally?
I have an application where I need to locate certain zigbee devices...
Dear Nordic support team,
We are using the SDK v2.6.1 to build targets for nRF52840 chips, and are using multiple configurations defined in a CMakePreset.json file.
It...
Hello!
I am currently running into throughput problems while using the Nordic Uart Service (NUS).
I am building a project for a peripheral and wanted to test the possible...
Hello,
We are implementing BLE FOTA for nRF52832. For that trying to load nrfutil tool. Its downloaded from official website. python is also installed successfully. when...
Is there a solution from Nordic available where I can have a LTE-M (or NB-IoT) and at the same time still receive the 1PPS output from the GPS module? It seems to be that...
Attribute reporting is automatically handled by the ZBOSS stack which generates the Report Attribute commands. Is it possible to set the Disable Default Response bit in the...
When I start the debugger (both internal and Ozone) the registers view only shows the CPU internal registers; peripherals are not shown.
If I start Ozone manually I can...
In my design, I choose to use the circuit suggested in Config no.5, but the USB interface is not effectively identified in the actual test. Through the test, the power supply...
This is same what same as in my previous ticket
With nRF9160 Ozone solution worked just fine but when trying to debug nRF9161 with Ozone I receive error on Ozone Console...
Hi.
I am using SDK v2.6.0 (Toolchain v.2.6.0). When I open VS Code (v1.91.1) I keep getting this warning -->Bad CMake executable: “”. Check to make sure it is installed...
I have a custom PCBA with which has the flow of:
- Boot
- Advertise some temperature data read from TWI with a 5 second timeout using `ble_adv_fast_timeout`.
- I then...
Hi to all,
I'm developing a beacon application on the nRF52840-DK starting from the example that I found in the VS Code (Zephyr).
I'm designing a custom board with only...