Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Dear Nordic Engineers
I used gd25lq32e to replace mx25r6435 and it is a 32Mbit Flash, when I add it to the Devicetree of Lwmwm(NCS 2.6.1), the build will report the following...
I'm currently working on a POC for the nRF9160 with an external host processor. I have the Serial LTE Modem example running on the nRF9160 and have the serial comms between...
Hi,
I have a simple question ... I think.
I have been limiting my USBD reads/writes to 64 bytes as NRFX_USBD_EPSIZE and NRF_DRV_USBD_EPSIZE are set to 64 bytes. I have...
Hi all,
I am using the nRF5340 DK. I am trying to run the ncs/nrf/samples/openthread/cli sample with no changes. I have tested this in both ncs v2.7.0 and v2.6.2. I am able...
I'm adapting the sample code for TF-M secure peripheral sample (NCS v2.5.0, nrf/samples/tfm/tfm_secure_peripheral ) to also add a UART peripheral. But this sample uses the...
If there are any compile errors in a LOG_xxx call, the compiler prints so many error messages that it becomes impossible to tell which is the actual error. E.g. below is the...
I've just purchased a PPK2 and before I did I check to see if OS X 11.7 is supported - it is ( https://docs.nordicsemi.com/bundle/nrf-connect-desktop/page/os_support.html...
Is it safe to connect the communication peripherals (SPI, UART, I2C, etc.) of an nRF52840 in system_off state to powered peripherals that might (or not) possibly transmit...
Hello Nordic Team ,
This is not a technical problem/question. I don't know this is correct place to write but I want to inform Nordic and whole community in Turkey. I am...
We are working on a broadcast assistant that should be co-located with a broadcast source, and it should only help with the stream provided by this broadcast source.
What...
Hello,
I'm designing a custom board with an nRF52840. I currently have an nRF52840 DK (PCA10056, v3.0.1) and would like to use the on-board debug out header (P19) to program...
Hello,
how can I increase the number of ZBOSS buffer (zboss_api_buf.h)? Currently they are 25.
We are using nrf52840 with nrf5 sdk for thread and Zigbee v4.2.0 without...
Hello,
I need to use timer1 in counter mode.
how can I use GPIOTE to start the interrupt of the timer( NRF_TIMER1->TASKS_START = 1) ?
when using directly the nrfx timers...
I try to add a custom signature key to the nrf5340_audio application from NCS2.7.0. I cannot use an absolute path because the project must be build-able by different people...
