But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello support team,
I am a beginner in this environment and I am facing a problem while trying to compile my project in Zephyr for nRF52840dk board. I am trying to run this...
I am currently using a J-LINK EDU Mini to try and learn how to use an external device to flash the nrf board. I am running into trouble because I have connected my external...
Hello, I am trying to get to make error handling while getting GPS signal. so that if there is no GPS, I move to Queclocator commands to get LBS location. the problem is that...
What is the problem with this error, I think the problem is not getting #include <zephyr.h> liberary, if it is how to fix it. any recommendation is appreciated
Hello, we have a design that includes nRF9161 for LTE purpose and a separate MCU.
The power sequencing for nRF9161 is as follows
VDD1, VDD2 is supplied with 4.2V
ENABLE...
Hello,
I am using version 12.3.0 of the nRF5 SDK for the nRF51422 development board. I opened the 'ble_app_hrs' example code in IAR Embedded Workbench and successfully built...
Hi All,
I have design my customer board but after production nothing looks to work. i can program the board through the Nordic board by using debug out. even a simple blinky...
I have a BLE code, when it runs on NORA-B106 it gives me -20dB difference on comparison to nRF5340 Nordic DK.
It was not expected such a big difference, what could be the...
I have been trying to implement the wifi scan or wifi provisioning code on a module (MS12SF1) which is a combine wifi + ble module
The setup looks like the image shown below...
Hi,
I'm developing with NCS v2.6.0 for Raytac MDBT53v-P1M module, which inhibits nRF5340. I already have my own PCB with all the required HW components.
As a sanity check...
Hi I would like to report a bug in the Devicetree visual editor.
When you add two fixed regulators and connect a separate sensor to each of them, both sensors will be represented...
I am trying to get a SST25 spi flash running, but the jedec,spi-nor driver does only partially work.
As i understand now the jedec,spi-nor driver only works with CFI compatible...
Hi, I am experiencing low power issues on a nRF52840 DK 3.0.2 board which I have not seen on another one with version 3.0.0. I do not know the root cause yet.
For my investigations...
Hi
I am powering the nRF52840 from a 3.3V DC power supply and connecting it with a IMU thats cannot go higher than 1.9V on the I2C bus
I use 1.8V.
Will the I2C coomuncation...
