I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Greetings!
Our device will use WiFi network to send data to the Azure's IoT Hub, where it will be further forwarded to our cloud. As the used network won't be controlled...
Hi Nordic support
We have ealier used your legasy SDK16.0 on nRF52840 where we where programming our device serial number in the UIRC area.
NRF_UICR->CUSTOMER[0-4] where...
Hello,
I am using the nPM1300 IC on a custom PCB with the nRF5340 + nRF7002 + nPM1300 configuration. sdk v2.8.0
I am trying to read the battery status (ADC value) via...
I have problems when I connect to my mqtt broker, it looks like it doesn't do a CLEAN_SESSION.. according to server logs.. I see when I connect to test clients ( pc ) with...
Hi, I recently purchased a nRF52840 dongle with the intention of creating a Bluetooth mesh provisioner with it. The first thing I tried was flashing the mesh_shell example...
Hi ,
Could anyone please with NRF9160-SIAA-B1A-R7 CAD Files (symbol, footprint, and 3d file) for KiCad ?
Thank you for your support.
Best regards, Mohamed Obaid
I'm using an nrf52840 on a custom board and send debug messages with printk to RTT. When mcuboot is added to the firmware it is no longer possible to read the messages from...
Hi nordic support Team.
I try to build blinking led example: nRF5_SDK_17.0.2_d674dde\examples\peripheral\blinky\pca10056e Load firmware for NRF52811 and NRF52840, i see...
Hi,Team,
I am developing Long Range and Pawr using nrf54l15-dk.
For the Long Range example I refer to E:\NCS\v2.8.0\nrf\samples\bluetooth\central_and_peripheral_hr and...
We previously used the nRF52832 (with Segger Embedded Studio) and implemented OTA updates for it, along with developing a custom APK.
Now, we are using the nRF5340 (with...
My nRF52840 DK needs to interface with a convential device using the data bus and address bus. The following diagram (P.27) from the nRF52840 PDK user guide.shows the data...
Hi,
I got a question on IQ Sampling with the direction_finding_connectionless_tx/rx example.
Settings:
Sample Spacing = 125 ns
Sample Sapcing (Reference Period...
Hi,
I have an nRF5340 DK, and my BLE project runs fine on it. However, when I flash the same code onto my custom board, bt_enable() returns error -11 , which seems to...
Hi
In the newer versions of nRF Connect for VS Code, the NCS and toolchain version can be configured per build-configuration.
Is it possible to configure the desired versions...
