But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi there,
I compiled a QSPI test program on board nrf52840dk. The SDK version is 1.9.1. Everything works fine. I would like to upgrade with SDK 2.2.x but I have several...
Hi Nordic.
I am developing with nRF52832DK and SDK 17.1.0
And it's connected with my Qualcomm board.
I want check GPIO input interrupt and output settings.
But...
Is it possible to view RTT console outputs in vscode during a debug session? I would like to see RTT console outputs right from the start, e.g. from bootloader, preferably...
Hi,
While using LE Audio, would it be possible to choose the data rate from 125kbps, 500kbps, 1Mbps, or 2Mbps?
nRF52 series do not support 500k coded PHY, so I would...
Dear support,
In NCS 2.1.2, it looks like download_client.c:socket_recv() is returning an erroneous unsigned type size_t , considering that it can can return either -1 or...
Hi,
I have late start issue on advertisement.
I have two device mode and we switch between when we want to. Device starts with Mode_1 with BLE enable.
When I switch...
Hi DevZone,
I am working on an application using:
nRF52840
FreeRTOS v10.0.0.0
nRF SDK v17.1.0
S140 v7.2.0
My question is if it is possible to enable the S140...
Hi,
With the nRF5340 DK boards (PCA10095), there are 3 VCOM ports (as viewed in VS Code) - printk debug logs for the app core are transmitted on VCOM2. However, the nRF5340...
hello to all,
I need to insert two CAN ports on the spi3 port of the nrf52840 with two different chip select and interrupt.
I have created an overlay file that defines...
Hello,
We have completed our custom board with nRF52810 and nRf52832, as asked in earlier questions needed SWD and SWDIO pins to upload code in SoCs.
So could you suggest...
Hi,
I recently found that the 5340 has a slow startup time on my custom nRF5340 based hardware, it takes about 3 seconds from power-on to the Main code running.
I did...
I use SDK17.10, when I send radio data using the esb，At this time, insert the usb, it takes a long time to enumerate the usb successfully; when I disable the esb,I plugged...
I'm trying to make use of the Async UART API with an nRF9160dk using NCS v2.1.2. As a starter application, I'm using the lpuart sample in nrf/samples/peripheral/lpuart. I...
recived error code 4
I am using nrf52840 for my application and use ble_app_template_pca10056_s140 for my project and receives error code 4 for nrf_sdh_ble_enable
Hi all,
I am trying to perform a FOTA upgrade over BLE with an nRF52832.
I started with the zephyr sample "peripheral_dis" at zephyr/samples/bluetooth, and then followed...
