I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hi,
I try to use sniffer (PCA10031 - V1.0.1_1111) between 1 NRF52 DK (PCA10040) with ble_app_blinky and 1 NRF52 DK (PCA10040) with ble_app_blinky_c.
After choose "Nordic_Blinky...
Hi,
I am using radio test example in SDK for fcc and ce certification. In this example we can confirm the Tx tests using a spectrum analyzer. Could you let us know how...
Hi All,
The MTU_SIZE of ble_app_uart is set to 64-byte. When write data over this, let's say 80-byte, the program will be reset.
I don't want to increase the MUT_SIZE...
Dear friends,
My PPK works unstable. Sometimes it works well, while sometimes it won't start. When it is started from the command line console, the error output is "initialization...
I have been working on "merging" SDK for Mesh's lightswitch client example and SDK v14.2.0 UART server example, mostly following the document on this site , with some changes...
I've gone through the user manual for the Nordic Power Profiler Kit, but I can't find any basic information on how to understand the plots and the measurements reported under...
I would like to have one central and two peripheral connection. Ad functionality required is same as NUS UART Example. But the example code connects to only device. Can any...
Hello,
i would like to connect two Redbearlabs Nano v2 just with eachother. The central one connects just to the peripheral, but the peripheral is still open for every...
Hello There,
I found following dongle based on nRF51822.
They claim same will work for bluetooth 5.0 also.
I know BT5 devices are not backward compatible, so not sure if...
Hi,
How can I share a GATT server profile constructed on nRF connect for PC with nRF connect for Android ?
'Save/Load setup' on Windows PC stores/Load json file
In...
I've got a set of boards that are behaving very strangely. I attempt to turn on the HFCLK but the HFCLKSTARTED event never comes nor does the HFCLKSTAT register indicate that...
I cannot suffer this tool anymore. As u can see in the pic below, it provides a cursor mode to measure the currents of X1/X2. However, users always need to know the average...
Hi,
I want to connect 4 antennas to nRF52832, they respectively points to North, South, East and West direction.
Also I hope the nRF52832 can do switch antenna job,...
I'm trying to use gcc and eclipse but I'm getting an error in eclipse that certain variable names cannot be resolved. I know that its not being able to get the variable names...
Hi,
I am developing a small development board of visiting card size, which is powered from a coin cell. I have two questions,
All i want know is there any polarity...
