But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
// <i> NRF_FSTORAGE_SD uses the nrf_fstorage_sd backend implementation using the SoftDevice API. Use this if you have a SoftDevice present. // <i> NRF_FSTORAGE_NVMC uses the...
Hi to all,
I have a problem and a question regarding the power measurement setup I’m working on.
Regarding the problem, I am trying to measure the power consumption...
Hi All,
I have a couple of nRF9160-DK which I use to program custom boards through the Debug Out port. Both DK work perfectly well until now. One of them can't program custom...
Hello everyone,
in our Project we want to use the nRF52840 DK with the X-NUCLEO-NFC08A1 (ST25R3916B) extension board as an NFC Reader.
In the SDK 2.5.2 are samples for...
I am running an experiment to use a static keys for pairing information without breaking the existing flow of pairing/bonding. What I am doing is I am storing the pairing...
I‘m try to download v2.6.0 SDK to update.But the terminal output as follow,I guess it related to bad network also I try with VPN
So that I try to pack v2.6.0 from another...
Hi there,
I'm having an issue with the SPI master in Zephyr. When attempting to transmit data it returns the error: 'Timeout waiting for transfer to complete'. Am I missing...
Dear Nordic-Support,
as I got a configuration error in my project when configuring CONFIG_TFM_PROFILE_TYPE_SMALL=y I tried to reproduce this with the AssetTracker_v2 application...
Hello,
I have a nrf52832-QFAA design that came back from the emissions test lab and they told me that the TX power on the Radio Pin was around -6dBm at the low frequency...
Hello,
I will explain my workflow so you can understand my problem using VS code and assuming everything is installed correctly, I`m using SDK 2.7.0:
Create new project...
I'm debugging the project that nrf_dm to learn how it work.
The build configuration as the picture:
I add my breakpoint as follow:
However,when I start to debug...
Hi, I have developed my own custom module with a program based on the NUS example.
I wanted to use the dongle as a configurator (in the sense that i connect it to the usb...
Hi:
My device is nRF52833-QDAA. And I'm totally a beginner in RF.
Right now I'm trying to figure out the component value of the matching network Z1 Z2 Z3 .
How can...
After problems with the programmer I have successfully flashed simple custom board with ACN52840 module, but the unit does not resetting after flashing using J-Link Pro. Starting...
Hi,
I have a project where I use nrfx_saadc and need to change channels and simple/advanced mode in runtime
If I start with simple mode, samples, move to advanced mode...
