But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi：
My environment is: nRF5_SDK_17.1.0_ddde560, keil, s113_nrf52_7.2.0_softdevice
When using usbd_cdc, I found that DTR must be set to start communication. Is there any...
Hi,
i develop my product ny ncs V2.6.0. in some case,i need store some user data to the flash，but i dont know how to read and write flash in cns sdk.if there is some samples...
Greetings.
Our team has encountered some difficulties in integrating nPM1300 into a new project. In the project we plan to use nPM1300 in conjunction with NRF52810. To develop...
* The nPM1300 LDSWSTATUS register @ Address offset: 0x4 doesn't contain values in the "Value" column.
* ID "E" occupies only one bit, but declares data on 4 devices:
...
Hi, I try to launch west build command from a terminal.
I am first generating environnement variable as stated in this post :
Then I call it, and finally, I launch this...
Hello,
I am working on a custom board designed around the NRF52840. Currently the bootloader on the board is the same as the one on the NRF52840 DONGLE. It is out intentions...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
My goal is to achieve a data throughput...
We are connecting nrf boards to solar charged batteries for power consumption. We will be remotely deploying the boards on field. The boards are connected to sensors, from...
I'm going from v2.6.1 to v2.7.0; I'm using a thingy53. I'm getting a voltage error prior to boot.
[00:00:00.002,929] <err> voltage: setup: -134 *** Booting nRF Connect SDK...
Hi,
I evaluate MCUBOOT and trying to understand how it works. I am using a nRF52840DK. I have base my demo on this course ( Exercise 1 - DFU over UART - Nordic Developer...
Hi,
We would like to disable all wakeup sources before calling sys_poweroff. How to achieve this using Zephyr API? Pin configuration should remain as previously configured...
basically, I want to use dm feature in connection-oriented communication. not in connection less, and I want to connect 1 central to 4 peripheral and measure distance.
Can...
nRF Conncet for Desktop v5.0.0
Hello,
I have some trouble to update the Toolchain Manager of version later than v1.2.6. The download fails. However, I can download the...
Hi,
We are working on a project using the nRF52832, which utilizes UART for a QR-code sensor, I2C for an OLED display, and SPI for external flash memory.
We are at the...
