Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
We have developed device that used 2.6 and when moving to 2.9 everything broke apart and I cant get it to boot and I cant get any output from device. Be it from USB or SWD...
I am having a persistent issue with the ANT+ examples in the nRF5 SDK on an nRF52832 DK PCA10040. The application firmware compiles and runs correctly, but the ANT+ signal...
Dear Matter Support Team,
I have a setup where an On/Off Switch device is successfully bound to a Light device in our Matter network.
I would like to know which specific...
I am using the Ublox NORA-B206 module and facing issues with the debug option in the VS Code extension. The debugger fails to start, and I receive the following error message...
Hi Team,
We have a custom board with nRF9151 SoC that shows complete RF failure. The modem initializes correctly and detects the SIM card, but cannot detect any RF signal...
I'm adjusting my program with nrf52832 and nrf5SDK.
I attempted to use the parameter PM_PEER_ID_N_AVAILABLE_IDS to control the upper limit of the bound users.
However...
Hello, I am testing the power consumption of the npm1304 for the first time. To do this, I am using the PPK2 connected to the nPM1304-EK on VBAT and GND of the P1 connector...
Hello, According to the nRF7000 specification, the sleep current should be around 15 µA. Electrical specification .
We have a custom PCB with nRF9160 + nRF7000, and the...
Hello DevZone,
I'm testing the Matter OTA by using OTA provider. Referring to: Performing Device Firmware Upgrade in the nRF Connect examples
But it's too slow. Is that...
I want to update 52840DK FW using Matter OTA, but I have not found SOP, could you tell me how to operate?
BTW, I use Raspberry Pi4 connected with RCP as border router. ...
After flashing the official example hci_uar onto the nRF5415-DK, I proceeded to use "udo strace -o btattach.log btattach -B /dev/ttyACM1 -S 1000000 -R“ to bind it as an HCI...
Hello, I’m working with the nRF9151 and testing DECT NR+ functionality. I already have the binary image of the DECT NR+ PHY firmware and it works fine. I’m just curious—is...
Hi,
I've successfully incorporated MCUBOOT into software we developed for the nRF5340. I'm also able to start serial-recovery by activating a GPIO, reserved for this purpose...
Hi, I’m trying to build the github.com/.../neuton-nordic-thingy53-ble-remotecontrol project using nRF Connect SDK v2.6.2 . I added the BMI270 sensor on SPI3 in my DeviceTree...
Hello,
I am at the very, very early stages of my project, doesn't it even a name yet. Right now I am thinking of using nrf52840 for a Bluetooth operation while being supplied...
