Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello!
I am using NRF1960 Feather boars and NRF Connect v1.7.0 for developing firmware.
I have a task to send data to server using LTE-M in 2 cases:
periodically...
I'm trying to connect to SPI modem and I did tried tons of solutions, nothing worked or even passed the build stage. can you guide me how I can at least see what's the error...
Hi,
I am working on a project which is having TF-M partition in it.
I want to now add bootloader to the application so that we can perform OTA update.
I try adding MCUboot...
Hello, guys!
We have nRF51822 rev3 SoC that runs the code developed with nRF5 SDK v12.3.0. SoftDevice s130 is enabled and used.
We want to use our custom HardFault_Handler...
Hello,
is it possible to switch between i2c and spi in the same pins in runtime?
I'm trying to evaluate a sensor where it can communicate over spi or i2c on the same connector...
When I am sending notifications or indications using the Nordic SDK, what do I need to be concerned about, the MTU size or the PDU Data length or both?
I negotiate both...
Hello,
I have a project in which I am using an nrf board with Zephyr. I am writing all this in CLion on Linux.
Until now all the code written is in C but I will have to...
Hello,
I am attempting to use the 802.15.4 Sniffer on the 52840 dongle and wireshark plugins to build my own parser for a proprietary protocol. I am running into an issue...
hi support team,
from our web we can see that we intergrated TLS1.2 and DTLS1.2 with modem, may i ask if it means only TLS1.2?
one customer told me they are using TLS1...
Hello, I am a private developer of wireless gaming mice in Japan. I am thinking of using Nordic's nRF52840 as the MCU, but can this chip be written to only by USB without...
Hi,
I am working with nrf52-ble-app-uart-relay example following this link, https://github.com/NordicPlayground/nrf52-ble-app-uart-relay using nRF5 SDK version 16.
I am...
Having an issue on a PC with Power Profiler v3.5.3
I'm measuring an esp8266 bootup and sleep cycle and this is how it looks like on a notebook running windows10 with v3...
I'm able to enable AT command and shell command terminal separately on nRF9160 DK. However, is there anyway to enable both AT and shell command?
1) in prj.conf
CONFIG_SHELL...
