But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Our team has been using Fstorage for a long time to store customer data in the device for customization. At random times, a very few units get erased completely when Fstorage...
Hello all,
Currently using an nRF52840-DK, GCC Makefile build tools including nrfjprog and nrfutil, Nordic SDK v15.0, SoftDevice s140 v6.0.0
I am currently trying to get...
hi support team,
our customer is trying to use gpio to simulate interface for external device communication.
and i tested our 5340dk pin 28 and pin 29, find out that gpio...
Hi,
I have a very basic question:
Where to find the sample source code mentioned in the infocenter of this link ?
infocenter.nordicsemi.com/.../uarte_rx_double_buffered...
I'm using arm-none-eabi-gcc from Fedora linux repositories. It got updated to version 12, and now it's not possible to compile the SDK - there is a problem with linking. It...
Hi,
I am using nrf_mesh_switch_client example and implemented disabling mesh on timer basis,
I have initialized the timer and started it in start() function. The following...
Hi,
I am using SDK 1.9.1 and nRF5340.
Scenario
I am investigating the following scenario:
files containing the firmware upgrade for the app and/or net cores will...
Hi there,
I'm currently using the nRF52 DK (PCA10040) and nRF5 SDK 17.1.0.
Our device needs to permanently connected to a battery, only wake up on a button press and then...
I came across a document called
2870.Measuring_distance_with_Nordic_Distance_Toolbox_slides.pdf
(found here )
Several questions
1. There are 2 slides for "High Precision...
Hi,
I tried every configuration options one by one to change the MTU size, but it doesn't work.
I connect to nRF52840 with Raspbery Pi and when I subscribe to a notification...
Dear All,
I am trying to figure out the maximum current consumed during the NFC operation.
I am using nRF52832 and writable_ndef_msg example from the SDK (LED, flash write...
My previous post and the response I got was hugely helpful to my understanding ESB on the nRF52. Now that I grasp the basics, I felt it was appropriate to create a new post...
Hi,
quick question..Which, if any, Nordic device has NFC that can be read and write without additional NFC ICs?
I've got an NRF52840 dev kit but apparently it only supports...
To the kind attention of Nordic support team,
we are (re)working on an old legacy project using nRF24LU1 and gazell protocol. We would need to know if there is some simple...
I am trying to add this ultrasonic sesnor driver ( inductivekickback/hc-sr04: Zephyr RTOS driver for HC-SR04 Ultrasonic Ranging Module (github.com) ) and testing it with the...
