But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
I am facing issue with nrf5340 DK. It is not powering ON properly and not detecting.
When I am trying to power on the DK by connecting USB, the LED5 (PCA10095) on...
I'm trying to get some data written and read from flash memory using the fstorage library as explained in the examples provided with the sdk.
I write to flash and get the...
Hi,
I am still investigating this but, I think it is best that we discuss it on this forum.
I am using SDK 16.0.0, nRF52840, secure_bootloader_usb on a custom board. The...
I just received notification from Onsemi that the ESD protection chip (CM1402-03CP) that I am using between my SIM card connector and nRF91 is obsolete. This is the same chip...
After upgrading nRF Connect SDK to v2.1.0 I noticed that my modified version of connectivity bridge (when running on thingy:91 nrf52840), stops working 30-60 seconds after...
Hi I'm developing a board to isolate external GPIO signals from a Nordic nRF52832 (Isolated input from 5VDC to 25VDC). For this I am using a circuit with the PC817 optoisolator...
Hi, I have similar error on this thread:
I cloned current latest releases of Android-nRF-Toolbox(3.1.3), Android ble library(2.5.1), and Android common library(1.0.27...
Hi everyone,
I'm using an nRF 5340-DK and want to update the application core firmware by using the nRF secure immutable bootloader. The bootloader and the network core...
Hi
I am currently running and adjusting the zephyr echo_bot uart sample on my nrf9160 DK. Currently , the sample makes use of UART0 to send a receive information which I...
I'm trying to connect a Thingy91 to the nRF cloud using just in time provisioning. I'm using MoSh. Here is the error:
mosh:~$ cloud_rest jitp Performing JITP... JITP device...
Hello,
When I change the optimization for a project to NO_OPTIMIZATIONS or DEBUG_OPTIMIZATIONS in the configuration (prj.conf), I always go in the hard fault handler ...
Hello,
i have a Nordic nRF52840DK and a Qorvo DWS3000 combination. I´m using SDK7.0.2, Segger Embedded Studio 5.10a and J-Link 7.58b.
I want to combine the ble_app_uart_c_pca10056_s140...
Can you please explain how NRFX_SPIM_FLAG_RX_POSTINC works? My data keeps always being loaded into the same address. Here is my code snippet:
uint8_t tx_buffer_MAG[1]...
