But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
I use the modified version of the USBD example(nRF5_SDK_17.1.0_ddde560\examples\peripheral\usbd) in nRF5 SDK from here . (My development kit is nRF52840DK.)
And I...
Hi, I have configured normal uart, where you send 1 tx_buf and wait for the rx_buf until you get a response. This setup was fine until the logging feature was requested. However...
Hi, I am developing a product using BLE with nrf52832. We are aiming for a BLE communication range of around 1.0m. However, if txpower is set to -20dbm, BLE communication...
Hi,
I found this forum post about the Verizon APN:
https://devzone.nordicsemi.com/f/nordic-q-a/46288/nrf9160-verizon-sim
This implies that I don't have to use "AT...
I want to parse the following JSON { "ver": 3, "mode": "online", "custom": { "apl1": [ "off" ] } }
Tell me about how to parse json and how to write code
The keywords...
Hi Everyone,
I am developing a PC App. with nrf52840 usb dongle (central) to communicate with nrf52840 BLE device (peripheral) on long term and transport data. Everything...
Hi,
I was working on nrf52840 DK and I left it a few weeks and came back to use it and I discovered that the whole USB connector (J2) got removed. Not sure if there are...
To the kind attention of Nordic support team,
I'd like to know what would be the best theoretically way, if possible, to control "when" multiple notifications are sent...
Hi,
I am developing with the nRF52833 DK using NCS v2.00.
I have edited the existing TX power service (TPS) to allow the client to set a desired TX power. I have added...
I'm using the nRF52840 with NCS SDK 2.0.2 and need to be able to change the BLE advertisement name of the peripheral device dynamically.
I have this working when using ...
Hello Devzone,
I am building firmware for an nRF9160 based device, starting with an ncs 1.6.1 sample app and LTE modem firmware v1.3.1. I'm in North America, and when testing...
I am using the SD card driver from nRF5 SDK v17.0.2. Device nrf52840, IDE Segger, Custom PCB. nRF52 DK as progremmer.
There are problems when deinitializing the SD card...
Hi,
I am developing a peripheral in ble, and I receive the following error when I disconnect a new connection within the connection callback.
bt_conn_disconnect ( conn...
Hi,
I'm writing an application which, depending on configuration, will either use ESB and Bluetooth, or just ESB.
I read through the article ( ) describing how to use...
