But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
I am testing an app using CoAP client/sever. I want to redirect the RTT log messages to UART0. I had a look at https://devzone.nordicsemi.com/f/nordic-q-a/32058/why...
Hi,
Currently, we are facing a huge problem with our custom boards. Between different boards the ADC values varying very much even with a given voltage input.
For instance...
Hello all
I am porting the code from the nRF52DK to the nrf52820, and so far so good, however, I am having a question, when configuring the TWI, will this get me the right...
Hi all,
Provided the nRF52840 board implements up to 4 SPI, I would like to use at least 2 of them simultaneously. I need to do it like this because I need one of them...
Hi, I am trying to merge Libuarte with the FreeRTOS environment. I am trying to use RTC-2 for libuarte and RTC-1/0 for Freertos. I am not sure what other things I should enable...
I'm working on a custom board that uses an nRF52832 module. It has a single button that is used to power the device On/Off and a >= 5sec long press from Off to force enter...
Hello,
we would like to use a pin on GPIO P1 as GPIO in non-secure mode, but only found the solution stated in this thread yet: https://devzone.nordicsemi.com/f/nordic-q...
Hello,
I am experiencing issues with an nRF5340 board and its SPI.
I am trying to add an Pmod OLED (128x32) screen to my board, but firstly I am trying to set up the...
Zephyr nRF52840
I am working with 2 nRF52840dk. The master side seems to be working as expected. i have monitored it and seen clock, MOSI and CS all working as expected...
Hello,
I have a debugging issue with VS code IDE.
Suddenly, i cant debug with an error:
However, flashing board is working succesfully.
What am i supposed to do...
We use spi flash with custom driver and goal is to set it to act as secondary partition for MCUBoot.
The question is how to adapt driver to be accepted by MCUBoot, maybe...
Hello,
First off, thank you for reading this. I know this is on the cutting edge, so bugs are to be expected.
Problem:
I loaded the dm sample found here: https://developer...
Hi,
I am using nCS and mcuboot in my application for development, on nRF52833.
I build a nCS project, the build bin file (prj.conf as ):
I broke up into packets...
