But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello,
The following error message appears when the original code "asset_tracker_v2" under NCS 2.0 is compiled with vs code IDE,
Can anyone give me some comments? Thanks...
Hello,
I'm just trying to run the LTE_BLE_GATEWAY sample program and I've flash all the nessesary firmware onto the nrf9160dk baord. However, when I turn on the nrf52, it...
Hi,
I am building the CoAP client and sever example programs on a third party module (Reytac MDBT50Q). I am using Reytac dev board MDBT50Q-DB-40. Unfortunately the example...
Hi all
Can the NFC tag of nRF52832 be integrated with multiple cards？
Such as t he access control card of my dormitory and my home can be replaced by one card
Thanks...
I use the connected mode of DF, i use the two receiver,one transmiter,but when i flash the procedure to my boards.i find that only one receiver can get the IQ samples.how...
I am trying to port some code I wrote for Gazell, which I guess acts more elegant since it uses PPI, a workqueue, timeslots, etc. I have an ESB connection in which I receive...
Hi,
I am currently developing with the nRF52 DK (nRF52832 SoC) and the nRF52833 DK (nRf52833 SoC). I have built and flashed the Bluetooth: Peripheral HT sample from Zephyr...
HI,
I'm using nrf51822 and Gazell protocol.
from the RM, i get that the combined length of S0, LENGTH, S1, and PAYLOAD cannot exceed 255 bytes, which i think i can set the...
hello everyone, recently I entered the world of nordic,
and I have been testing some of the functionalities, of one of the devices,
specifically the nrf5304 dk model,...
Hello,
I created a device on AWS and corresponding certificates/shadows on the us-west-1 server. I'm able to successfully connect and send to this endpoint, but want to...
Hi Sir / Madam,
May i know if there is any layout guidelines that available for nRF5340-QKAA?
Appreciate if you could help to provide to ease the development of the...
My app uses mesh shell to subscribe to messages on a custom model and that works just fine
I need to subscribe to a different address on the same model but get an error...
Hello,
I using the "nRF5_SDK_17.1.0_ddde560" and want to capture the current RTC count though a gpio (low_to_high event) via PPI. I want to use the RTC2 (used by app_timer...
Hey,
We are trying to create PoC which includes NordicSemi thingy 91 or nRF9160DK, AVSystem portal and AWS cloud.
By default AVSystem uses string "urn:imei:<imei number...
