This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
1. Please provide me with an example in which UART0, UART1, uart2, and uART3 are enabled
2. The sending and receiving rate of each UART must reach 1,000,000 baud rate...
Hello,
I have been working with a BLE custom board project for a few months and the product requires buttonless DFU feature. The bootloader that I initially used was derived...
Hi,
I'm developing a project with nRF52832 and BOSH BME688 sensor.
I downloaded the library from github to use the sensor (here it is the link https://github.com/BoschSensortec...
Hello,
I am developing BLE peripheral Reader FW using nRF Connect SDK v2.0.0 on VSCode
I have developed my application using NRF52840 DK (development board) and it works...
Hi everyone,
Does anyone ever get confused about BLE connection interval? As explained in this post , it determines how often the Central will ask for data from the Peripheral...
Hi,
We have a board with ESP32 and nRF52833, connected via UART. We want to upgrade the nRF firmware via either BLE or UART. The nRF image size is large so dual image slots...
I am getting this error in Ozone:
"The target stopped in HardFault exception state.
Reason: A fault with configurable priority has been escalated to a HardFault exception...
Hi Team,
I'm trying to build i2c example code with nRF9160 using Zephyr RTOS. But when i use "west build -p auto -b nrf9160dk_nrf9160 sample/drivers/i2c_fujitsu_fram" to...
Hi All,
I am working on BLE+SD card Library, s132. Although i am getting certain errors which i am unable to counter.:-
*** Using Compiler 'V5.06 update 4 (build 422...
hello,
i have been using nrf52832 with sdk 15.2 , while different interupts occurs i have been changing the advertising bytes with different aid like this
m_beacon_info...
Hi, I see there are similar and narrow questions for specific chipsets: nrf5340 and nRF5240
Does this mean that Bluetooth LE Power Control (LEPC) feature is not at all...
hi:
Use the https_client routine to send data after the socket is established, and then send the data after getting the response. The errno returns as 128, which can confirm...
I've downloaded a fresh copy of NCS 2.0.0 and created a brand new application in an empty workspace based on the Hello World sample. The only modification I've made is putting...
Can I use SVC function in my application code to copy bootloader image into flash instead of using mbr commands? If this is not possible, what are the other alternative options...
