But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello,
We have a firmware developed for Full Thread Device. But now as i want to reduce power consumption i want to convert FTD device firmware to SED firmware.
SDK...
After reading this https://devzone.nordicsemi.com/f/nordic-q-a/3830/what-is-the-value-of-the-gpio-pull-up-and-pull-down-resistor
and seeing that the internal pull-up is...
I'm trying to get readings from an LPS22HB sensor with the nrf52810 using the lps22hb driver in SDK 17.0.2_d674dde.
The lps22hb_init() call completes without any errors...
Hi, I'm using nRF52805 and SEGGER.
The firmware could be programmed to the chip successfully when I use Debug->go. I can connect with the BLE signal.
However, when I use...
Hi! I am struggling with figuring out how to properly set the sampling frequency for the qdec device. I noticed that making changes directly to the members of config struct...
Hi,
I'm setting up SAADC as explained in the examples: First start conversions with buffer 0, then with buffer 1. On the SAADC callback I queue the current buffer for conversions...
I'm developing an app that communicates with iOS apps using Nordic's services.
I got this error during development.
I have three questions about the "peer removed pairing...
Hi,
I want to enable 8 channels of saadc in SE mode with 10 bits of resolution. the number of samples in every packet is 32, which means every channel have 4 samples in...
The problem I meet similar to https://devzone.nordicsemi.com/f/nordic-q-a/60684/nrf5340-pdk---debugger-in-ses-remains-in-bt_enable-forever .
/* Wait til nameservice ep...
I'm interested in collecting the modem core temperature for my applications. After some digging in modem_info.h / modem_info.c , I saw the temperature data structure exists...
I want to use PPK2 to test the power consumption of my user device, I have connected the PPK device to my pc with USB cable and turned on its power switch, but when I opened...
Hi, I am trying to run the sample I2S echo program(nrf-sdk/zephyr/samples/drivers/i2s/echo) on 9160 DK, and am having issues reading any valid data on I2s RX. Codec chip is...
Hello
NRF52840 with own hardware
nRF SDK V17.0.2_d674dde
nRF SDK for Mesh V5.0.0
IDE: SEGGER 5.60
I started with the "ble_peripheral/ble_app_template" example...
I am trying to use the dongle as a BLE sniffer. I have followed the directions on how to program the dongle including downloading and installing the jLink software.
When...
SDK 17.0.2, SD 7.2.0. with secure bootloader, when performing DFU without BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE, nRFConnect will successfully update the app. With BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE...
