Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
Our company use nrf24L01+ for many years,the maximum output power of 24L01+ always about 0dbm in our application.But recently we meet a problem that the 24l01+ output...
Hello, as mentioned in subject, I have done DFU on nrf51 DK. it is tottaly working fine. As soon as I try to work with Nrf51822 QFAC custom board. It goes in to bootloader...
Hi,
I intend to use the nRF9160 as an LTE module. I will send data to be transmitted to the nRF9160 and receive data from the nRF9160 via SPI. I have read in numerous places...
I just want timer2 to run at 1Mhz so I can grab a microsecond counter as a timestamp. I don't care that it'll overflow after 32 bits. Put together what I thought should be...
Hello, I'm using the Radio Test software (SDK 15.2) to control the N52840 radio IC. Our circuit design requires the use of an external RF amplifier IC. Our software puts the...
Hi everyone,
I am stuck with an apparently simple problem which I am not able to fix.....
I have an SPI device connected to a custom NRF52840 board. I am using NRFX_SPIM...
As per the section - "Adding support for programming nRF5340 in SES" in the document https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf5340.html , I had...
Can you please guide me how to compile the nRF Connect SDK asset tracker with the AT command library enabled. I need to set the CONFIG_AT_CMD_RESPONSE_MAX_LEN configuration...
I tried to connect my nrF52 DK board to various devices, via USB. None of the devices was able to see the board.
In addition, nrF Connect / Studio wouldn't see the board...
Hello,
I am trying to understand how to use an external button. In the first stage I am trying to replace the functionality of button0 on the DK with a GPIO.
I took the...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I'm working with the ble_peripheral example...
Hi, We are using the nRF52840 in a 3V battery powered product. We have an on board 1.8V LDO regulator that supplies Vdd and Vdd_IO. We have a problem with the NFC antenna...
Dear all
I currently have a single nRF52832 SoC (custom PCB) transferring data to a single nRF51 dongle via BLE, which in turn passes the data to my PC via UART. I have...
