But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I have some issues flashing or debugging my Thingy91. The problem seems to be related to my specific Thingy91, as I have another Thingy91, which I'm able to flash...
So, I am updating our advertisement data on a regular rate using a timer from freeRTOS on custom piece of software the is for the nRF52840. When only the app code is loaded...
Hi,
I'm trying to deal with long write events (37 bytes long) but on adding a second long write characteristic I'm facing the NRF_ERROR_NO_MEM error on adding it.
The...
Hi Sir,
Since Zigbee_Thread 3.2 released, we prepared two 52840-DKs for consumption test.
One is the door lock example (device #1 Thread_Zigbee_3.2.0\examples\multiprotocol...
I notice that the question has been asked as far back as 3 years without any answer!
There are several parts of the datasheet that mentions internal reference voltage sources...
Good morning Mrs
I have a bluetooth module SKB501 which integrate a NRF52840 chip. In that NRF52840, i want to test a code (ble_app_uart) include in the "nRF5_SDK_15.3.0_59ac345...
Hi. We are using RTC2 in our application to trigger an event at 256Hz. We also have a compare running to trigger a compare event at 32Hz.
I have found that over an hour...
Hello guys,
I am using nRF52840 and SDK 15.3.0. Trying to use SPIM3 device because of the speed.
In my sdk_config.h file, I set both NRFX_SPIM_ENABLED and NRFX_SPIM3_ENABLED...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I want "nRESET" to be set without pull-up. How can I use "nRESET" without pull-up?
Hello,
While importing the needed libraries for a project I stumbled upon an error in the app_error_handler_gcc.c and app_error_handler_iar.c files. The error is
nrflibraries...
I am using a SPI peripheral on the nRF52832. If the SPI bus is busy when I call
err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST);
the routine returns...
Hi, I'm working on a simple SAADC acquire in scan mode.
I create the two following function:
I was able to init and read the adc without problem.
If I remove the...
Hi All, I'm doing some investigative around existing mesh models. In the Mesh Model Bluetooth Specification, Section 7.1, we have a specification, for example:
Generic OnOff...
Hi,
I am considering now the timings during a BLE connection, especially for long range. For that I came across the range delay given in the latest BT Link Layer Specification...
