But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Testing BLE mesh of proxy light switch example with 3 nrf52840(1 as client and 2 as servers) pdk boards with nrf mesh apk(android phone). Phone able to scan nrf 52840 light...
Dear Team,
I am using ST-Link V2 connector to program a nRF52840 board. When connected to a laptop and try to connect to the target, it says 'ST Link USB Communication...
I am currently trying to extend the range of the bluetooth mesh application. The infocentre infers that the function:
typedef struct
120 {
121 radio_tx_power_t tx_power;...
Hi,
I wonder if someone can make recommendations for types of 'smart bracelet' ('smart wristband') devices that use a BLE chip of Nordic's nRF51/nRF52 range. Can you point...
Hi,
I'm currently developing software on nrf52832. Unfortunately, I can't use the SDK for different reasons.
I'm currently looking at the RESETREAS register. If I...
I use the following code to write 32-byte to L01-module. (The wireless-communication works successfully ).
The following ( 420us+200us ), accompany only 32-byte wireless...
Hi.Is there any inbuilt ic present in nrf52840 DK board to monitor battery management ??if so, how to use that for measuring battery life?can anyone help me out plz!!
Thanks...
Good afternoon, I have a new small, but I think important, question. I did not find a concrete answer on this forum. The question concerns the correct switching of buffers...
I had try to use nRF connect to connect between nRF52840 Dongle and the bluetooth of application.
(I'm not sure the model of bluetooth of application.)
It's connected...
How many crystals/oscillators do I needfor a NRF51822 WLSCP chip?
I looked at datasheet and I'm assuming I will need a 16 Mhz crystal, a 32Mhz crystal, a 16 Mhz oscillator...
I am using IAR workbench and working with the nrf52 DK, using the S132 v.3.0 softdevice. I used the blinky example code to connect the nrf52 with my android phone over BLE...
Hello,
I got TCP Server example working on nRF52DK with Raspberry Pi.
I set everything up and can ping global addresses of DK on all interfaces (wlan0, eth0 and bt0) from...
Hello,
I am using NRF52832, SDK v15.1.0.
For advertising on single channel, I added " p_advertising->adv_params.channel_mask[4] = 03; " in ble_advertising_start() ,...
SEGGER Embedded Studio 3.12
nRF52 SDK 15.0.0
In order to generate peripheral driver library files，how to create library in project(have .c&.h file in this project).Only...
Hi,
SDK documentation says "You cannot write to UICR.BOOTLOADERADDR when using the default J-Link target driver in IAR". Some threads suggested it is only nRF51 issue, but...
