But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Greetings,
Using SDK v3.1.1 I've configured 3 PWM outputs using the pwm0-2 modules via a DTS overlay. After reset or power cycle (and prior to making any PWM driver calls...
After cancelling a flash operation to my nrf7002DK (PCA10143 1.0.2), I'm unable to flash my discovery kit again. I have tried both the regular west flash for our application...
Hi,
I use flash read operations at the BLE interrupts, because I need some of the stored informations. However, while I am doing another flash operations and BLE interrupt...
Greetings,
What's the maximum clock rate supported by the SPI1 interface on an nRF52840? My DTS overlay indicates it should use 32MHZ for one device and 8MHz for the other...
I am tried to access the server using http_client .I am tested that my implementation to access the local server works properly but the thing is i am tried to access the ...
I am looking for the datasheet for the nRF31512. I am looking to see what the pinout for this chip is. It is not for any new project as I know it is old and discontinued....
Hi,
1. Does the P1.02 (NFC port) on the nRF54L15 support PWM? 2. If it does, please provide the overlay configuration method and sample code.
Best regards,
Peter.Mi...
Hello,
I am building an example app that uses MbedTLS and non-offloaded sockets, because offloaded ones do not fit my needs - updating security credentials needs disabling...
I get the following error when trying to program the device:
The log shows this:
2025-12-10T09:08:50.194Z INFO Initialising the bundled nrfutil device 2025-12-10T09...
Hello,
we have an nPM1300 EK plus the profiling adapter board and are trying to profile some of our batteries.
We have already successfully completed profiling for...
Hello, I am currently struggling with setup and configuration of firmware for nRF5340. The idea is to use two stage bootloader setup, XIP split to external flash and build...
when trying to implement ISR for writeprotect and powergood pin it throws error code 134 which corresponds to not supported.
call stack for reference.
What am I...
I had a fully working BLE setup on my nRF52 (Zephyr), which worked fine on older Android versions. After updating a phone to Android 16 (tested on Google Pixel 7 and Samsung...
Hi, Nordic support team!
I'm having trouble downloading the NCS in China.
The command nrfutil sdk-manager install v3.2.0 --region cn fails with a SHA512 checksum error...
I have designed a custom board using the nrf54l10 chip (similar to nrf54l15). I want to use SPI to communicate with a sensor. So I assigned the pins P2.6 for SCK, P2.4 for...
