This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi there! Our app developer are experiencing some difficulties with Bluetooth LE and image/file transfer on iOS. The device (our product) uses the NRF52840 chip. Any help...
Hello,
Using nRFConnect 2.1.0
I am trying to build the peripheral_iso zephyr sample, for the nRF52840 DK
It compiles fine as is (with the original board qemu_cortex_m3...
For some reason my ticket got deleted earlier, so here I go again.
I'm trying to change the configuration of the network core bootloader. For the `hci_rpmsg` and `mcuboot...
Hello,
I am going through the tutorials in the DevAcademy. During the learning process, I noticed the nRF Connect SDK is updated several times. I started from 2.1.0, now...
I am trying to make a multiprotocol network using BLE and Thread. I have flashed nRF52840DK using the `s140` Softdevice and flashed the ble_thread_dyn_template as well.
...
Hi,
I am currently using the NRF52840 DK to evaluate the NFC functionalities of the SoC. It works very well with a smartphone.
I'd like to understand the NFC on the NRF52840...
Hi,
We are developing a matter curtain product the power by battery.I setup SED mode for low power. The larger the POLL PERIOD value I set , the worse the real-time performance...
Dear Support team
I don't quite understand the part as the picture below after I read the specification, I would like to kown What are the output drive modes in the picture...
I want to make an NFC card with Ntag 213, which is an NFC Type 2 tag.The card needs to write data to a specific block via NFC.
However, the NFC Type 2 tag library does not...
Hi, as stated at page 15 in the Direction Finding white paper(nWP-036), it says 'When the last switch pattern is reached and IQ sampling continues, the switch pattern loops...
//nRF52840 DK//PCA10056//central=apple-smartphone//Wireshark Version 4.0.1 (v4.0.1-0-ge9f3970b1527) sniffer.//
Wireshark is working perfectly on Advertising packets, but...
Our project was previously functional when we were developing using the nrf52840dk_nrf52840 with an overlay to reconfigure for our custom pcba. We created a custom board config...
Hi,
Is the nRF9160 capable of operating on the CBRS band (b48)?
I know it is not listed as a band that is supported by HW but I am curious if there is a software workaround...
Hi Nordic Team,
I am working on the BIS demo, I have three nRF5340 DK audio boards, so I set one as Source, two others as Sink, so is there any resources that when Source...
Hi,
After lots of issues with build and deploy, I eventually have a working version of a BLE App running on a XM122 Radar module. This module have to be packeaged with the...
