Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi, we are using the nRF52 DK (nRF52832) to read data from the i2s bus and store it as a wave-file on the connected SD-Card. When pressing button 1 on the DK, recording starts...
(For some reason, I use "...' replace the original string) Here is the log for using AT to do HTTPS POST:
2022-02-07T12:19:39.057Z DEBUG modem >> AT#XHTTPCCON=1,"...",443...
Hi,
I'm working with NRF Connect SDK, and once in a while when I add new configuration options to the prj.conf, I get an error that some region overflowed by X bytes,...
Dear friend,
Since the customized nRF5340 board does not have an external 32.768KHz low-frequency crystal oscillator, the following is added to prj.conf in netboot:
The...
Hi
This is the first time I have tried to use the nrf52840 dongle and the programmer v2.3.1, it can see the dongle( com10), but as soon as I select Device tis is the response...
I facing a problem. When, progrsmis run for testing on nRF5340DK using SES, the CPU resets automaticaly. The RAM does not respond timely is shown , please see the attached...
Hi everyone,
There is an open ticket that I need support with because the responsible engineer will be out of the office until the new year.
In a nutshell:
I design...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Please tell me about "nrf_sdh_enable_request". This API only makes a request, so I understand that the SoftDevice...
Hello Respected members, I hope this post finds you well. Can someone help me with how to store UART data in FLASH? The Idea is that I have to send the Date Or Serial Number...
Hello !
As part of nrf_crypto it is no any examples how-to use chacha20 without poly e.g only stream cipher.
Would be nice to use it via nrf_crypto and evaluate hw accelerated...
Hello. I had worked on nrf52840 development kit with BLE UART code(pin 6 and 8 as Tx and Rx). I used the same code on Fanstel EV BC840M board. I changed the Uart pins to 9...
Hi,
we are considering the Serialisation library for the SoftDevice S132 in one of our projects and would like to know for how long this library will be supported?
Thank...
Hello! I have made good progress in studying nrf9160, and nRF connect SDK but....
I'm having problems with basic things. I want to create a project in the nrf connect sdk...
