Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi,
We have come across AT%XRFTEST command problem for TX test on nRF9151 EVK. We have used nRF9151 modem firmware version 2.0.2 and executed following AT command on nRF9151...
Hi Nordic team,
I’m building an LE Audio gateway on the nRF5340 DK using the TMAP_Central sample (NCS v3.0.2, with minor local changes). The setup captures audio, encodes...
I'm working with nRF52840 microcontroller, nRF SDK 17.1.0 and Softdevice S140 version 7.2.0
The peripheral devices sends 29 bytes of data with a BLE notification from a...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
I'm currently using firmware advertising/scanning with 1M PHY, but I'd like to use Coded PHY instead. I tried changing the advertising parameters as shown below, based on...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
I have LIS2DW12 (Gravity board) connected to my NRF54L15-DK with the following overlay:
& pinctrl {
/* Pin control for I2C21 */
i2c21_default: i2c21_default...
Hello,
I have set up the light and light_switch BT Mesh examples on my nRF52840DKs. I have used the nRF Mesh app to provision them successfully and I can see that they work...
Hi,
I am using NRF Connect environment and would like to enable by program to use MCU Boot functionality with dual-imaging support and FOTA updates.
My Kconfig.sysbuild...
I need to change the path of ncs. after try sometimes, I failed. So, I need remove all the settings and retart my work from initial status. I uninstall vs code. and install...
Dear Nordic Team,
I am trying to configure logging through J-LINK RTT for my firmware.
My prj.conf contains the following:
CONFIG_PRINTK = y
CONFIG_CONSOLE ...
My current product uses the NRF523840 with CODED_PHY periodic adverts. I want to improve the range.
I'm considering a +14dBm (SAR limited) product variant with the NRF54L10...
The nPM2100 datasheet (v1.0) states in multiple areas that the VOUT pin is discharged when the device enters Hibernate mode (and certain other modes).
Is this discharge...
Hi
It seems that the default minium DTLS handshake timeout is about 1 second. That means, there is a retransmission if a response isn't received within this timeout. In...
Hi there,
I am trying to program my custom board hosting a raytac mdbt53 module (powered by a separate USB cable). I have to use the custom connections in P20 connector...
