We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
To the kind attention of Nordic support team,
About nRF52833 product specifications (8. recommended operating conditions)
"Note: The on-chip power-on reset circuitry...
Hi,
I'm trying to run a pc-ble-driver on Arm64 arc
I've compiled the pc-ble-driver to arm 64 from this release: ARM64-linux pc-ble-driver origin/release/4.1.2
I used...
Hi,
I'm currently working on a way to connect raspberry pi as a gateway into the nrfcloud. For this case, I used nrfcloud/gateway-raspberry-pi. Neverless, when I tried to...
I am developing a product using nRF9160 and found the power consumption is higher than the datasheet. So I want to use Matlab ti simulate the circuit to see where the error...
I am currently trying to implement a Thread functionality on an nRF Dongle connected to a windows machine. Its intent is to be able to recieve messages from other thread components...
Hello Nordic team,
I have a nrf9160 powered from a 3.8v bench supply.
I also have a usb to uart cable , with uart wires going into NRF9160. Usb side, plugged into my computer...
Hi
1、 The following table does not indicate whether the QDID belongs to 5.1 or 5.2.Are the QDIDs of softdevice classified as Bluetooth 5.1 or 5.2?
2、The following qdid...
Hi all!
I flashed and got both SoftDevice s130 and the example code onto my nRF51802 without prior modifications.
I flashed softdevice according to: https://infocenter...
Dear Nordic Team,
Hope you all are doing fine.
I have the NRF52-DK based on the NRF52832 BLE IC from Nordic. I wanted to implement a basic BLE Beacon that broadcasts continuously...
Hello,
I am starting to work on a sample project, wherein I need to replace the existing "main.c" file I have with "main.cpp", by copying the contents of "main.c" into...
Hi zone,
I've just got nrf9160dk and test gnss feature. Issue is: 1. Device get long time to fix. Even which many SVs in tracking and using
2. After got fix, device...
Hello there,
Recently I tried to configure the MCUBoot on my custom Adafruit feather nrf52840, based on the Windows.
Firstly, I followed the instruction below to configure...
Hi
I use PCA10040DK,My connection description：
DK's External supply + to the PPK2 logic port VCC pin DK's External supply - to the PPK2 logic port GND pin DK's External...
