Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi,
I use nRF51822 powered by CR2032 battery. Same decoupling as dev board PCA10001.
Would you recommend different values of decoupling capacitors for battery powered...
I have SPIM working at 8MHz on nRF5340-PDK
I want to increase the SPIM speed to 16MHz.
The errata for nRF5340 states "In 128 MHz mode, SPIM max receive frequency is 16...
Hi Team,
We are using nrf9160-DK. We have tested assert tracker application, where we got the real time GPS data(DK location) we are happy with that. We also tested the...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Environment :
Host : Macbook Catalina
SDK : 16.0.0
Toolchain : ...2018-q2... (the pre-configured toolchain in the SDK)
SoftDevice: (not used yet, planning to use...
Hi, I'm using mesh_ SDK and nrf52840, I want to know whether the relay node in a BLE Mesh can wake up at a specified time to receive or send packets, and sleep the rest of...
Hi,
I am developing a device based on nrf52840 soc, and the rule of my device is peripheral. I want to know, if a connection was established, could my device start the...
Hello,
we are currently in the development of a low power, battery powered device that needs to count slow pulses (period between ~10ms and several seconds).
At the...
I have a custom nRF52840 board that transmits sensor data (using UART) to a PC with an embedded Bluetooth adapter. I have a code on Matlab that works just fine (using blelist...
Dear Sir.
I am using Master SPI to drive 2 slaves.
Both spi are referenced within Interrupt routine ,
When both spi;s slave are referenced I get an error
err = spi_transceive...
This question has been asked before. I have been using the previous threads to cobble together what is below. I opened a new ticket as reopening (really) old threads is generally...
usb hid how to send 6 bytes of data, app_usbd_hid_kbd_key_control can only send 1 key value, I see that app_usbd_hid_kbd_ctx_t can fill 6 bytes, please see
typedef struct...
Hello,
We're needing a lot more RAM than what nRF91 has, does current nRF Connect SDK support parallel PSRAM on Zephyr somehow or is the development on a roadmap?
Hi there, I want to use CppUTest on the nRF52 to start developing my personal and not so personal projects. I am using the SDK for nRF52, with PCA10040's board. For the moment...
