This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
hi...
i am using mesh 3.1 latest version , i have changed the light switch example code , where i am sending the character . i have completed the scanning , provisioning...
Hey. I'm looking for a complete free RTOS for the commercial development of our startup. We will use the SEGGER Embedded Studio IDE and SoC Nordic nRF52840. As I understand...
Hi,
i'm current working on example light switch, when i use function generic_onoff_client_get(); in client to get status from server, callback function app_generic_onoff_client_status_cb...
We're running a multi-drop single duplex RS485 bus, so it's important to stop driving the bus as soon as a transmit is complete so the next device can transmit without two...
We're running a multi-drop single duplex RS485 bus, so it's important to stop driving the bus as soon as a transmit is complete so the next device can transmit without two...
Hello,
Can I send data from nrf52832 to nrf24l01p? If yes, please suggest me the simple code for it. I tried to send data but it failed. Here is my piece of code :
Transmitter...
I have the nRF52 DK board and I cannot see the device in the list in the nRF Connect app (iOS). Here's what I have tried:
Connected the nRF52 DK to my computer with micro...
Hi all,
I have tried to flash the blinky programm to the BMD 300 AR evaluation board by nRF command line tools but I can't flash the .hex file to my evaluation board. The...
I followed this tutorial :Bluetooth low energy Characteristics, a beginner's tutorial
i am beginner to study BLE.
I wanna the answer Challenge 1: Why are you not allowed...
Hello,
Our setup:
IDE : Segger Embedded Studio for ARM V4.12, nRFgo studio
SDK : nRF5_SDK_15.2.0_9412b96 + SDK for Mesh3.1.0,
Softdevice : 6.1.1
Computer Platform...
Hi, I'm using SDK12.1 example ble_app_ancs_c.
Is it possible keep advertising (non-connectable is ok) when ancs connecting?
And how to do it?
I tried call advertising_start...
Hi,
I have been having issues with the compile hex files I get when following the steps to build the pc-ble-driver (). While I am able to build the hex files when I place...
I got Orange sim connected to LTE-M network on nrf9160 DK, verified it on LTE link monitor. But when i tried adding a LTE device on nrf connect cloud, i am not able to register...
Hi,
I tried to build the lte_ble_gateway sample in SES, however it gives the error below regarding the UART.
Any suggestions how to resolve this issue?
Hi,
As mentioned in the subject, I am confused with the SPIS example from nRF52 SDK 15.3.0. I wonder where NRFX_SPIS and _INST_IDX are defined in the header file?
SPIS...
