We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
i am working on ble_app_uart central and peripheral, so basically peripheral will sleep wake up and send advertisement packet to central . Now the issue is if peripheral is...
Hi, My Lord. When I run the example, I use short-name(BLE_ADVDATA_SHORT_NAME) advertising always "Fatal error",It's no use reducing payload.
On the other hand, how to add...
Dear experts..
I'm currently developing and testing nRF52832 application with nRF52-DK.
This are three questions about "actual" advertising packet length on air.
First...
1.HOW TO enable a node relay , friend,proxy or low power ability ?
2.if node A publish a message to a GROUP ADDRESS(0XC001) for node B( subscribeed this group address) ...
I looked at the nRF91_DK_User_Guide and it is very confusing to understand how to set up the board for current measurements. The figure says to solder SB44 and SB45 but the...
Hello,
As of today, April 17th 2019, I am using latest version of SDK and SES. I am using Jlink from nRF51DK and a nRF52832 module bought from ebay.
I tested several examples...
extern void bsd_recoverable_error_handler(uint32_t error) AND
extern void bsd_irrecoverable_error_handler(uint32_t error); Will return various error codes - is there a list...
I'm trying to use the NUS to send data over from NRF52 dev kit to the NRF Connect app. Using Putty for UART works fine. Now I adapted to read out ADC values from 2 ADC ports...
Hi, can someone tell me what chip this is and where I can find the data sheet? Or at least if this is a custom fabrication, what chip from Nordic is it based off of? Thanks...
Hello,
I am using ble_app_uart_c example for my nRF52832 based central application. I would like to modify Tx Power and MODE of my device.
As per datasheet, I should write...
I'm finding above examples in SDK example file. but, can't find.
where the perfectly tutorials?? It's too hard for me only refer to the library's code.
I cannot config...
It has possible to add iBeacon advertising structure to add ble_app_blinky example code. I'm implement connectable iBeacon advertising every 5second it's connected nrf connect...
According to some benchmarks shown here: https://www.novelbits.io/bluetooth-5-speed-maximum-throughput/ , I should be able to get a connection speed of around 120,000 bytes...
Hi,
could you please tell where can I find a table showing all the NVIC interrupt vectors?
I searched in the nRF52840 datasheet but I did not find something relevant ...
