But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
SDK14.0.0/S132 5.0.0
The SDK provides an example of turning on SSP Debug mode for LE Secure connections
Is there a way to enable SSP Debug Mode for BLE Legacy Paired connections...
Hi , I have some issues with the ADC. When moving in and out from low power mode the ADC isn’t working correctly. I am using the nrfx_saadc driver. When moving to low power...
Hello Nordic Team,
I am using nRF52840 Dongle (PCA10059) and nRF5 SDK. I was tring to use PWM example code (PATH - "nRF5_SDK_15.3.0_59ac345\examples\peripheral\pwm_driver...
Hi.
I build application which is mix of writing QSPI to external NOR FLASH, using linkage list base on the fstorage FDS example all in the embOS (RTOS of Segger).
I have...
Hi all,
I using nrf52832 and segger IDE
I am trying disable softdevice and enable it while chip running. In my project, I use RTC1 for app timer.
When I disable SD,...
My setup:
- nRF52840 Preview DK (though i have tried this on a newer version too)
- 3.3V separate supply
- DMM (Agilent 34465A)
DK Connections:
- SW9 is set to...
Hi,
We are trying to take the nRF sniffer trace but there is some issue is showing , i will explain it below.
we are following nRF Sniffer "User Guide v2.2" for initialization...
Hey,
So I recently got some test SIMs from AT&T to use for our development. I'm trying to get them working with my nRF9160 dev kit but can't seem to get a connection to...
This question has been asked several times but none of the answers is solving my problem. I am developing a ble application which was loading with no problems. I switched...
Hey,
I neet to change the PHY mode of my connection between nRF52840 DK and OnePlus6 (Android 9) to CODED PHY. If I try to change it, I'm always getting an fatal error and...
An ARM sales rep told me the CryptoCell-310 was discontinued and replaced by CryptoCell-312. Assuming this is true, what encryption module will nRF52840 be using in future...
Hi
I added print on line 245 and on iphone 6 can receive complete image data and display but on Iphone X , iphone X Max the data will stop before image data complete
https...
Does nrf 52840 have an inbuilt temperature sensor? I am getting some values when i see them through hercules software, so are these garbage values or internal board temperature...
Hello, I am developing a BLE application using nRF51822 on SDK 12.3 and SD 2.0.1.
I have an application with NUS service, in which I set the device name by sd_ble_gap_device_name_set...
