We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello community!
I use the dongle PCA10059 (nrf52840) for my hardware. I already enable -DARM_MATH_CM4 and link library libarm_cortexM4lf_math.a with CMake. I can include...
Hei,
I am following the Install the toolchain section and after running
choco install python
the step does not verify because it does not find pip3.
'pip3' is not...
One of our resellers is requesting a classification code for the RF protocol. We use a Proprietary RF protocol based on ESB (Enhanced Shockburst). Is there an IEEE or a different...
I am experimenting with trying to improve the current range of gzll nRF52840 dongle to dongle (which is not that far from what I need). I am developing using nRF5_SDK_15.2...
Hi,
The top level page nRF5 SDK Documentation Library page ( https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/index ) contains a link to "S140 SoftDevice...
Hi,
I am trying to implement the DFU example from Mesh 3.1.0SDK and 15.2.0 SDK. I am following the process mentioned here .
I am using a MacOS for development.
I am...
Hi
I am using device manager and store connected devices value on next advertise device should be broadcast as bonded
static uint32_t device_manager_evt_handler(dm_handle_t...
Dear Nordic ：
Our mass-produced smart trainer( 16M external oscillator, 20PPM ) supports ANT+ FEC and ANT+ Bicycle Power , so there are two channels alive wtih 4Hz frequency...
Dear Nordic ：
Our mass-produced smart trainer( 16M external oscillator, 20PPM ) supports ANT+ FEC and ANT+ Bicycle Power , so there are two channels alive wtih 4Hz frequency...
Hi,
I used nRF52840 dongle device to run BLE multi-link Central and nrf52832 to run BLE Blinky example to test the communication of 20 nodes. How can I set and verify that...
I am making a BLE device that uses 7 ADC inputs. Most of the inputs need to read at 1hz or so. Two of these inputs are of interest
The first is a heart-rate signal that...
Hi,
I want to measure ADC for 3.3V
Using formula
RESULT = [V(P) – V(N) ] * GAIN/REFERENCE * 2 (RESOLUTION - m)
Rearranging eqn:
Vin = ( RESULT*REFERENCE)/(2 (RESOLUTION...
Hi,
Does every nrf9160 chip have its unique chip ID? if yes, is it the one which can be read by the AT command AT+CGSN ? and can it be used as the board serial number? ...
Hi,
I used nRF52840 dongle device to run BLE multi-link Central and nrf52832 to run BLE Blinky example to test the communication of 20 nodes. How can I set and verify that...
