But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
i used SDK9.0.0 to implement the function that bond to cellphone.
case 1:when i set the IO_CAPABILITIES to BLE_GAP_IO_CAPS_DISPLAY_ONLY,the process of bond is ble device...
Hello,
i m using sdk15.2.0 in nrf52840.
please help for increase adv data size from 31 byte to 45 to 50 bytes..
i had tried with "BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
RTC connect through I2C and GPS connect to UART. I am getting large amount of data from gps contentiously . In the mean time i should read time from RTC . But i am getting...
i have 2 setups, one on a pca10040 running sdk 14.2.0 s132 and the other one on a pca10028 clone running sdk12.3.0 s130 with a 51822_xxaa mpu
the ble_uart examples from...
I just want a simple and clear PWM driver to generate a duty cycle on a GPIO pin - 25% on and 75% off. Just that. What is the most power efficient method?
The example PWM...
Hi,
Yesterday I installed the image ' RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha.img' on a Raspi 3B+ and cpnnected a Nrf52840 DK via native USB. Using the 2.0.0 Thread...
Environment:
Nordic SDK 15.2.0
Eval kit nRF52840-DK / PCA10056
SES debugger on Windows 10
I was trying to integrate nfc_callback() for ...EVENT_FIELD_ON / OFF from...
Hello,
I have a problem with MQTT Publisher example on my nrf52832 DK.
1. I am using ubuntu & nordic's SDK15.2.0 for this mqtt example. On raspberry pi 3b I have installed...
I need to communicate with a sensor through SPI. However, in order for the sensor to switch to SPI mode, its CS pin must go down. So before I do SPI transfer, I clear that...
Hi,
I want to interface RGB LED- APHF1608LSEEQBDZGKC (Kingbright make) with nRF52840 operating at low power mode on 1.8V (@Vdd). The 1.8V external source is capable to drive...
Hi Nordic,
we use the demo "ble_app_hrs_freertos" (nRF52832, SDK13.0)
I'm trying to get it into low power (system on mode) , and the idle task keep on running and the...
Hello,
I had to hard code new MQTT broker settings. Specifically the NRF_CLOUD_HOSTNAME. Whenever I update the nerf_cloud Kconfig to select a new broker, the autoconf...
Hi
On our project we see often softdevice asserts with the version 6.1.1 of the S132. The application we have is offering a BLE GATT service that allows fast serial communication...
