Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I am using nrf52840DK and trying to implement a weather station application using thingy53 application example. I am using a Bosch BME280 sensor and could read the data...
Hi, we are using nRF52832 for our project. SDK version is nRF5_SDK_17.1.0_ddde560. SoftDevice is S132.
The project requires TWI to read data from a sensor and send that...
Dear All:
I found that there is a shell interface for the nrf5340_audio project.
I wanted to test the sd card playback from the shell interface.
For the broadcast sink...
I have two nrf9160DKs that are talking to each other over BLE. Things are working fine but I want to eliminate some of the external noise in my environment. Is it possible...
Hi,
I'm using nRF Connect v2.6.2 with Wireshark (3.6) and it is setup with the nRF sniffer + Nordic network keys configured.
I can decrypt packets from another Zigbee...
Basically I want the nrf5340 to reconnect to a paired peer upon reboot. The code seems to suggest that this should happen via directed advertising.
I am testing this with...
Hello:
I am Enrique Martinez. Currently I work with nRF52840 in nRFConnect SDK for VS Code. I have problems with documentation about Multi-Image builds ( https://developer...
Is it necessary to use the 32768 crystal on the target device in order to flash that device using a connection to the nRF52 development board, or can the device use the internal...
Hi
this is the error when I tried to connect to peripheral and also get the error on scanning after that connection error
I am using the sample code for this application...
Hi,
I am using nrf52832 to test the function of mcuboot. The reference routine used is D:\ncs\v2.6.0\zephyr\samples\application_development\sysbuild\with_mcuboot. After...
Hey,
I'm trying to follow a few guides on sniffing BLE connections (eg https://hackaday.com/2021/03/23/a-crash-course-on-sniffing-bluetooth-low-energy/ ) with an NRF52...
Hello everyone,
I am currently working on a school project in which I need to record the energy consumption (mA) of ESP32-H2s over a 190 minute period using the Nordic Power...
Dear Sir,
I just want to capture DTM packets using NORDIC sniffer. The Wireshark is the newest version. My chip is 52840 with nordic snffer bin file. Thanks.
with regards...
Hi everyone,
We're trying to synchronize data coming from two different BLE modules (nRF52833 based) on a mobile application. The following is the information of two devices...
Hello,
I want to have "make" included in the NCS toolchain. As far as I can see, on Windows the tools (in toolchains/xxx/usr/bin) is msys2 based. My question is where to...
