After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi, I am testing out the UART Peripheral sample on the nRF52840 DK. Since I am communicating with another MCU, I have remapped the RX and TX pins to P0.26 and P0.27 respectively...
The MenuConfig page of SEGGER IDE (ncs1.9.1)：
How should I configure this interface if I want to configure usb DFU and trigger upgrade mode via button: 1.boot_usb_dfu\Use...
I am trying to flash blinky program to nRF52840 Dongle using nRF52840 DK thorugh SWD pins. I successfully implemented that using Segger Embedded Studio by following the steps...
I am working on a project that is being ported from the nRF52840 to the nRF5340 and the once unified radio and app codebase needs to be split to the app CPU and network CPU...
Hi,
I found a odd thing when I try to get the value of ERRORSRC of uarte0 in the problem.
Sometimes the project of my customer have an uart error, when they read the value...
Hi,
I am testing NFC read/ write examples . in nRF 5 SDK 17.1.0
I am trying to write the tag using PN532 using the adafruit tag reader example but i receive error like...
Hi
I am using nrf52832 on that I want to use spi communication.
Is it possible to use half-duplex communication on spi protocol?
In full-duplex mode after sending...
I'm currently trying to make a new board definition for our PCB, which by mistake has been fitted with an nrf9160-SIBA rather than a SICA. When trying to make a new board...
Hi,
I need assistance in nordic thingy52 ble communication. I am using node and bridge code from the https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
If I...
Hi Nordic Support,
I have been waiting for many years to see our end-user devices (Android, iOS, Windows, and Linux) such as smartphones, tablets, and computers to support...
Hello,
Right now our application developed using s140_nrf52_6.0.0_softdevice, SDK 15.0.0 for NRF52840 chip.
Need help on migrating to BLE 5.
Which SDK & soft device...
Dear all, my project consists of 6 nRF52840 custom boards, one acting as central device and the other five acting as peripherals (star connection).
The central device receives...
Hello,
I'm migrating my project from sdk 17.0.2 to sdk 17.1.0. In the project I use BLE NUS, and it's control data. In SDK 17.1.0 there are no functions for sending ctrl...
Hi,
I have been experimenting with the different nrf_modem functions to get AT responses. I want to receive the current time (don't need to be accurate) using AT+CCLK?,...
Hello,
We use pin 4 to set our CHIP SELECT in order to perform spi_transceive.
We use the SPI protocol to "talk" between a microcontroller and the LSM6DSL component. ...
