This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Good day.
I am currently developing with two NRF52840 DK boards, and I also have two NRF Dongles. On a dongle a sniffer for ZigBee. I am working with SDK 3.2. This is my...
The spec for the nRF52840 indicates a maximum power level of 8.0 dBm and -51dBm for 2nd order harmonics and -48dBm for 3rd order harmonics. What is the output power level...
Hello, is it possible to get the altium data from nRF52840 dongle (pca10059.SchDoc and PcbDoc) ? It's so time wasting to clone it from pdf. Thx. Ralf Adler
Hello Devzone,
I'm in the development stages on a battery based sensor device, utilizing nRF9160 System in Package for LTE-M connectivity and application processor. I have...
Hello Everyone,
We are using a nRF52810.
We have ran into an issue where our 32MHz XTAL can take longer than 400us and thus the Errata 3.6[68] CLOCK: EVENTS_HFCLKSTARTED...
Hello all!
I would like to use the PWM driver, yes, the hardware that is on board the chip. To get going certain code parts from the PWM driver that comes with the SDK,...
I would like to set the radio channel using 'uint32_t nrf_esb_set_rf_channel ( uint32_t channel ) '.
In 'nRF52840 Product Specification v1.7', '6.20.12.2 Operating frequencies...
Hello !
1.
In nRF21540 PS current consumption in TX mode is specified like this :
TX_20dBm State: TX POUT = 20 dBm 110 mA
But it is not clear if it depends from actual...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I want to send an array "data_array" of uint8_t...
Hi,
the tool chain of NCS1.9.0 is at /opt/nordic/ncs/v1.9.0/toolchain
I just install NCS2.0.0 by NRF Connect Desktop.
However, I found there is no "toolchain" in /opt...
Hi,
We need help in getting an system call / API in Zephyr which updates the consumption of memory ram and flash
can you please suggest any mechanism which verifies...
I am using nRFConnect on windows 10 with the nRF540 Dongle for the first time.
I am successfully able to connect and view parameters on the nRF52832 using the Dongle.
...
Hello,
In my project i am using nr52840 actually its a custom board and i want to send the sensor data to custom app sometimes data updating and sometimes data not updating...
I am try to flash BLE SDK binary by Nordic, but using --sectorerase --verify with --reset seems to fail :
Two options combined :
I'm using the nRF51 SDK version 17...
