Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Step 5 of the Matter instructions at developer.nordicsemi.com/.../python_chip_controller_building.html
Shows getting the discriminator data. What is shown looks like the...
Dear Nordic Experts, A few short questions about mesh advertising in regard to Softdevice s132, 7.3.0, Mesh SDK 5.0.0 and nRF5 SDK 17.0.2:
How do you change the advertised...
Hello,
I'm running asset_tracker_v2 from v1.9.1 on a LTE-M network that does not give the time (UTC clock) info.
When no time information is given, the application should...
Hello
I have some questions about flash_fstorage example.
After reading the macro, it seems that fstorage will be located in .fs_data flash zone.
start_addr is set...
Hi,
Softdevice - 112
sdk 17.1.0
I am trying to evaluate the memory of the device. I am using nRF52810 and the datasheet says 192KB flash and 24KB of RAM available. ...
Hi I am using Unity test framework for generating unit test report and i also want to generate the code coverage report of the code for that i need how many lines of code...
Hey
I'm currently writing a thesis on IIoT and implementation in remote areas. We're trying to setup the nRF9160DK as EON device with all implementations on the board...
Hello,
I am experiencing trouble with NRF9160 chips that get stuck after typically 1 to 2 days of operation. This happens on all 6 boards that I have available. I'll describe...
Hi,
I am coming across an issue with app_scheduler and FDS.
While waiting for an event in FDS to complete (write, read, init, gc, etc) I go into a while loop calling app_sched_execute...
Hi,
What is the lifespan of nRF52810, operating at room temperature ? How long can it reliably work? Do you have some figures on this ? If yes, is it same for other nordic...
Hello everybody
I am using the nRF51 Dongle to connect via a third party app to a measuring device. This always worked very well on my first computer, the app could detect...
Hi,
I updated my Segger Embedded Studio for Arm from V 5.68 to V 6.20a.
Calling CMSIS Configuration Wizard fails with all examples with message : "Error starting process...
Hi All,
I have a nRF52840DK and looking for a solution to connect the VCOM serial port to the PC, without using USB. I will need to connect the serial port to another board...
I'm working on porting a code base over from nRF5 SDK to nRFConnect/Zephyr. Our previous implementation uses ChaCha-Poly encryption, accelerated by the CC310. I wish to continue...
Dear Nordic team,
For the security reason to be safe from the hacking, we like to completely disable the debugging and flashing port during production.
Would you please...
