Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
I am using the nfc library (nfc_t4t_lib) on the NRF52832 chip with SDK 17.0.2. When I approach the NFC antenna with a nfc reader (like a smartphone) and leave the reader on...
Hi everybody. I'm trying to design a mesh network in which most of the nodes, if not every, should be a relay due to parallel positioning of the devices and each one of them...
I am working on Windows, using NRF Connect SDK 1.5.0 (have also tried the SDK 1.5.0r-rc1, with an updated nrf_802154_serialization module to be able to compile).
I am using...
Hello, I have run into this problem again with regards to using the lwm2m_client sample. I can start running it fine but I get the error "Cannot init lwm2m engine" and "Cannot...
when compiling "ble_app_multirole_lesc_s140_pca10056" of sdk nRF5_SDK_17.0.2, crypto library not getting included, I am getting error, library is placed as shown in pic, also...
Hello,
I know that you can generate a single zip that contains dat and bin files for sd+bl and dat and bin files for the app.
Is it possible to generate a single dat and...
HI, I'm new here, hope following the rules for Questions.
I'm using nRF Connect v.3.6.1 and as toolchain SEGGER Embedded Studio for ARM (Segger edition) V5.34a.
I need...
Hello there,
I am using nRF52840 PDK and nRF5_SDK_for_Thread_and_Zigbee_v1.0.0 SDK for BLE and Thread development. I also have a BLE smartphone app communicating with nRF52840...
Hi,
-I have a custom board using nrf 52832 and I have interfaced LIS2DH12 using an SPI interface. -I am using SDK 15.2.0. -I am collecting raw data using FIFO mode and send...
I want to realize audio playing function in 9160, according to the specification, there are 9160 I2S interface. However, the specification only describe the definition of...
I am testing UART example using nrf52 DK(nrf52832), SDK17.0.2. (\examples\ble_peripheral\ble_app_uart\pca10040\s132) Setting UART initialization to a specific pin will halt...
I use ANCS example from SDK 15. But I found that I'm not able to get more than 32 chars for ATTRIBUTES (BLE_ANCS_ATTR_DATA_MAX). And it's a little short to get Title, Sub...
Hello,
in our application we have one central (nRF52840DK) and up to four peripherals (nRF52832). We want to achieve two goals in this application:
Goal 1: We need a synchronized...
Hello I have built a custom board using an nrf52810 chip and have been trying to upload some examples from the nrf52SDK (specifically BLE examples with the s112 SoftDevice...
