Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hello, I discovered strange behaviour related to reset pin on my nrf52833 prototype and SDK17. My board has only reset button connected to reset input and 10K pull-up resistor...
Hello,
I'm having an issue with a hard fault when trying to write a specific value to a peripheral chip (TDC7201) register after multiple successful writes to the same register...
Hi all,
We're starting to move to the nrf52840 platform and have a question about the adc.. We'd like about ~13 bits of effective resolution- right now we use an ads1115...
Hi, I would like to try the Alexa_Gadget sample supplied in nRF Connect SDK v1.4.0 on an nRF52382DK but the sample does not build. I have tried both SES and command line builds...
We've been asked to run BLE transmissions using Ble_LR500Kbit, that is, Long range 500kbit/s TX. 125 kbit/s and 500 kbit/s RX on the nRF52840. The transmissions would be data...
Hello,
how much effort would it take to switch an application from the nRF52832 to the nRF52840 chip?
What we want to do is, we have a running application with the nRF52832...
To the kind attention of Nordic support team,
I'm interested in implementing some sort of validation stage using a keycode, as you mention in:
https://infocenter.nordicsemi...
Looking at the code of function nrf_log_frontend_dequeue, in nRF5_SDK_17.0.2_d674dde/components/libraries/log/src/nrf_log_frontend.c:716, it seems to me that the code chunk...
Hello!
I'm trying to implement a thermostat cluster handling. I've managed to implement read/write thermostat attributes handling using zigbee device callback. The problem...
I am trying to design a remote control for my garage door and I need to develop a low power remote control that talks to my Thread garage receiver.
I have looked into OpenThread...
Hi, I am attempting to flash various bluetooth samples onto the nRF5340pdk, and I am getting errors on multiple levels.
First, when I attempt to build the samples (I have...
Hello, I am trying to load some example on my nRF52840 dongle. I am developing without using a board but only the dongle, SEGGER and nRF Connect 3.6.0 .
Following this guide...
Hi everyone,
I've noticed in SDK examples such as the ble_app_hrs that call APP_ERROR_HANDLER after softdevice API Call.
What is the reason for this API call?
Any side...
Hello,
I am working on ble_app_uart example on nRF52840DK.
According to the documentation, when the device is advertising, the LED1 should blink. But I am not able to...
Hi all,
I was going through the release notes of the S132 V7.2.0.
Under known issues, DRGN-10340 states the following:
"The BLE_GAP_EVT_SEC_INFO_REQUEST event will not...
