After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi Sir,
In this project, we design with nRF51822-QFAA (Flash: 256KB, RAM: 16KB) and developed the application and bootloader through the nRF51-DK (pca10028). The file...
Hi Sigurd,
Thank you for your reply. I have executed the code given by you (below link) in Segger studio(V 3.50) I observed that the output or load (pin 31) which is connected...
We have the device, where 2 power supplys can be applied. One of them is external regulator with 3.3 V output. We used it for additional load in our device. Another one is...
Hi,
I referred uart example in nRF SDK 15.0.0 and tried to implement on proxy_client program by adding all files which there in example. but still i'm facing compilation...
Hello!
I'm facing some problems when I try to broadcast a message from my receptor to the transmitters, I'm using 3 nRF24L01P. I read some things about setting the same...
I have 2 PCA10056 preview development boards.
The newer one (0.11.0 2018.3) works as expected.
The older board (v0.9.0 2016.48) the built-in LED1 thru LED4 do not...
I want to use application board and connectivity board with mesh sdk in nordic chip. Is there serialization is available for mesh like using in nRF SDK15.0.0 peripheral driver...
We are developing an application on the nRF52840 kit with SDK 15.2. We are using Keil as compiler. I have started developmet my application with the example ble_app_cscs....
Hi,
I would like to try the DK in a high voltage mode. I tried switching the power source switch to either LIPO or USB (using LIPO battery and USB respectively) but in vain...
Hi, I'm new to thingy, I want to log the data received and viewed in mobile app / web app from thingy 52 development kit which contains nRF52832. Is it possible to log data...
Hello everyone,
I am in trouble because of a vlotage of current problem, I think it is most a voltage problem.
Let me explain,
I have a NRF51DK that I programmed to...
Hi,
there is no migration guide available for 15.2 , my application currently uses 14.0.
1. when will the guide be available? can use the one for 15.0 till then? will...
I have followed this posting by Hung Bui , with light_switch_proxy_server being combined with the ble_uart.
I am using: nrf52 dk, Mesh SDKv2.0.1, nrf5_sdk_15.2.0.
By commenting...
Hi,
Errata 202 limits the use of vdd as a power source to external components and I, therefore, would like to use a GPIO instead.
My question: is there a need to use a...
