Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
hw: nRF9160-DK, v1.1.0
Using the McuBoot-Loader of NCS 2.5.1 and the NCS 2.6.1 zephyr dfu module seems to be not longer aligned with it.
A app using NCS 2.5.1 zephyr's...
We are developing Matter/Thread based Smart Lock product. One of the product requirements is that the product should be able to connect to a BLE mobile APP at all times i...
Hi,
The CPU temperature module is located in the network CPU in the case of nRF5340. I have read this thread : Zephyr API to read the nRF5340 die temperature - Nordic Q&A...
Hello,
we use nrf5340 with Connect SDK v2.0.0 and we have adopted rules for indicating the update process and the operation of the bootloader in the device. Therefore, I...
I am working with the Ebyte e83 Dev board and Also got the ARM-JTAG programmer.
I have been trying to follow the nrf connect for VS code series and seems to get stuck on...
Before I got a white screen after selecting a ble chip (52840 dongle in my case), I deleted my folders home/ (.config/nrfconnect .config/nrfconnect-bluetooth-low-energy, ...
I just migrated from MacBook Air with M1 processor to MacBook Pro with M3 processor. I installed VS Code and nRF Connect SDK v2.6.0 from scratch on my MacBook Pro. hough my...
Hi，
I followed the steps below and the error "zephyr\zephyr_pre0.elf section 'text' will not fit in region' FLASH'" appeared when I compiled. I did not change any code....
Greetings team,
We are using the nRF Connect for Desktop v4.4.1 and Programmer tool has been updated to v4.3.0
Using this version the MCUBOOT settings are unable to turn...
Hello, I try to config vendor id and product id according to https://docs.nordicsemi.com/bundle/ncs-2.0.2/page/nrf/ug_matter_configuring_protocol.html .
1) When I change...
Good morning,
I work with the nRF52840DK board and the BC840E and I would need to make some changes to the SW of the "radio_test" application, but trying it out I find it...
Hi,
I am going to consider NRF52811-CAAA in a design. Can you please help with these questions:
1- What is the expected End of Life for NRF52811-CAAA chip?
2- If I have...
Hello,
We have a custom board for nRF52805. We have one LED connected to the GPIO. I wrote the FW for Blink LED every second.
I build the FW using the command " west build...
Hi,
I encountered a very strange issue. We are developing the firmware using v2.6.1 SDK and using Visual Studio Code + Nordic plug.
Platform: nRF7002-DK
SDK: v2...
Hi everyone,
I am currently experimenting with the NRF7002 WiFi stack and Zephyr. I want to build a Wifi bridge from my Bluetooth mesh network. I do have some experience...
